dts/marvell/armada-7040-db.dts

1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
8 #include <dt-bindings/gpio/gpio.h>
9 #include "armada-7040.dtsi"
13 	compatible = "marvell,armada7040-db", "marvell,armada7040",
14 		     "marvell,armada-ap806-quad", "marvell,armada-ap806";
17 		stdout-path = "serial0:115200n8";
31 	cp0_exp_usb3_0_current_regulator: gpio-regulator {
32 		compatible = "regulator-gpio";
33 		regulator-name = "cp0-usb3-0-current-regulator";
34 		regulator-type = "current";
35 		regulator-min-microamp = <500000>;
36 		regulator-max-microamp = <900000>;
40 		enable-active-high;
41 		gpios-states = <0>;
44 	cp0_exp_usb3_1_current_regulator: gpio-regulator {
45 		compatible = "regulator-gpio";
46 		regulator-name = "cp0-usb3-1-current-regulator";
47 		regulator-type = "current";
48 		regulator-min-microamp = <500000>;
49 		regulator-max-microamp = <900000>;
53 		enable-active-high;
54 		gpios-states = <0>;
57 	cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus {
58 		compatible = "regulator-fixed";
59 		regulator-name = "usb3h0-vbus";
60 		regulator-min-microvolt = <5000000>;
61 		regulator-max-microvolt = <5000000>;
62 		enable-active-high;
64 		vin-supply = <&cp0_exp_usb3_0_current_regulator>;
67 	cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus {
68 		compatible = "regulator-fixed";
69 		regulator-name = "usb3h1-vbus";
70 		regulator-min-microvolt = <5000000>;
71 		regulator-max-microvolt = <5000000>;
72 		enable-active-high;
74 		vin-supply = <&cp0_exp_usb3_1_current_regulator>;
80 	clock-frequency = <100000>;
86 	flash@0 {
87 		compatible = "jedec,spi-nor";
89 		spi-max-frequency = <10000000>;
92 			compatible = "fixed-partitions";
93 			#address-cells = <1>;
94 			#size-cells = <1>;
97 				label = "U-Boot";
110 	pinctrl-0 = <&uart0_pins>;
111 	pinctrl-names = "default";
118 	phy-names = "cp0-pcie2-x1-phy";
123 	clock-frequency = <100000>;
127 		pinctrl-names = "default";
128 		gpio-controller;
129 		#gpio-cells = <2>;
151 	pinctrl-0 = <&nand_pins>, <&nand_rb>;
152 	pinctrl-names = "default";
156 		label = "pxa3xx_nand-0";
157 		nand-rb = <0>;
158 		nand-on-flash-bbt;
159 		nand-ecc-strength = <4>;
160 		nand-ecc-step-size = <512>;
163 			compatible = "fixed-partitions";
164 			#address-cells = <1>;
165 			#size-cells = <1>;
168 				label = "U-Boot";
189 	flash@0 {
190 		compatible = "jedec,spi-nor";
192 		spi-max-frequency = <20000000>;
195 			compatible = "fixed-partitions";
196 			#address-cells = <1>;
197 			#size-cells = <1>;
200 				label = "U-Boot";
215 	sata-port@1 {
217 		phy-names = "cp0-sata0-1-phy";
227 		compatible = "usb-a-connector";
228 		phy-supply = <&cp0_reg_usb3_0_vbus>;
234 	phy-names = "cp0-usb3h0-comphy", "utmi";
241 		compatible = "usb-a-connector";
242 		phy-supply = <&cp0_reg_usb3_1_vbus>;
248 	phy-names = "cp0-usb3h1-comphy", "utmi";
255 	bus-width = <4>;
256 	no-1-8-v;
257 	non-removable;
262 	bus-width = <4>;
263 	no-1-8-v;
264 	cd-gpios = <&expander0 12 GPIO_ACTIVE_LOW>;
270 	phy0: ethernet-phy@0 {
273 	phy1: ethernet-phy@1 {
285 	phy-mode = "10gbase-r";
289 	fixed-link {
291 		full-duplex;
299 	phy-mode = "sgmii";
307 	phy-mode = "rgmii-id";