Lines Matching +full:disable +full:- +full:hibernation +full:- +full:mode
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/leds/common.h>
15 compatible = "emcraft,imx8mp-navqp", "fsl,imx8mp";
18 stdout-path = &uart2;
22 compatible = "gpio-leds";
23 pinctrl-names = "default";
24 pinctrl-0 = <&pinctrl_gpio_led>;
26 led-0 {
30 default-state = "on";
34 reg_usdhc2_vmmc: regulator-usdhc2 {
35 compatible = "regulator-fixed";
36 pinctrl-names = "default";
37 pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
38 regulator-name = "VSD_3V3";
39 regulator-min-microvolt = <3300000>;
40 regulator-max-microvolt = <3300000>;
42 enable-active-high;
43 startup-delay-us = <100>;
44 off-on-delay-us = <12000>;
49 cpu-supply = <&buck2>;
53 cpu-supply = <&buck2>;
57 cpu-supply = <&buck2>;
61 cpu-supply = <&buck2>;
65 pinctrl-names = "default";
66 pinctrl-0 = <&pinctrl_eqos>;
67 phy-mode = "rgmii-id";
68 phy-handle = <ðphy0>;
72 compatible = "snps,dwmac-mdio";
73 #address-cells = <1>;
74 #size-cells = <0>;
76 ethphy0: ethernet-phy@0 {
77 compatible = "ethernet-phy-ieee802.3-c22";
79 reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
80 reset-assert-us = <1000>;
81 reset-deassert-us = <10000>;
82 qca,disable-smarteee;
83 qca,disable-hibernation-mode;
89 clock-frequency = <400000>;
90 pinctrl-names = "default";
91 pinctrl-0 = <&pinctrl_i2c1>;
97 pinctrl-names = "default";
98 pinctrl-0 = <&pinctrl_pmic>;
99 interrupt-parent = <&gpio1>;
104 regulator-name = "BUCK1";
105 regulator-min-microvolt = <600000>;
106 regulator-max-microvolt = <2187500>;
107 regulator-boot-on;
108 regulator-always-on;
109 regulator-ramp-delay = <3125>;
113 regulator-name = "BUCK2";
114 regulator-min-microvolt = <600000>;
115 regulator-max-microvolt = <2187500>;
116 regulator-boot-on;
117 regulator-always-on;
118 regulator-ramp-delay = <3125>;
119 nxp,dvs-run-voltage = <950000>;
120 nxp,dvs-standby-voltage = <850000>;
124 regulator-name = "BUCK4";
125 regulator-min-microvolt = <600000>;
126 regulator-max-microvolt = <3400000>;
127 regulator-boot-on;
128 regulator-always-on;
132 regulator-name = "BUCK5";
133 regulator-min-microvolt = <600000>;
134 regulator-max-microvolt = <3400000>;
135 regulator-boot-on;
136 regulator-always-on;
140 regulator-name = "BUCK6";
141 regulator-min-microvolt = <600000>;
142 regulator-max-microvolt = <3400000>;
143 regulator-boot-on;
144 regulator-always-on;
148 regulator-name = "LDO1";
149 regulator-min-microvolt = <1600000>;
150 regulator-max-microvolt = <3300000>;
151 regulator-boot-on;
152 regulator-always-on;
156 regulator-name = "LDO2";
157 regulator-min-microvolt = <800000>;
158 regulator-max-microvolt = <1150000>;
159 regulator-boot-on;
160 regulator-always-on;
164 regulator-name = "LDO3";
165 regulator-min-microvolt = <800000>;
166 regulator-max-microvolt = <3300000>;
167 regulator-boot-on;
168 regulator-always-on;
172 regulator-name = "LDO4";
173 regulator-min-microvolt = <800000>;
174 regulator-max-microvolt = <3300000>;
175 regulator-boot-on;
176 regulator-always-on;
180 regulator-name = "LDO5";
181 regulator-min-microvolt = <1800000>;
182 regulator-max-microvolt = <3300000>;
183 regulator-boot-on;
184 regulator-always-on;
191 clock-frequency = <400000>;
192 pinctrl-names = "default";
193 pinctrl-0 = <&pinctrl_i2c2>;
198 clock-frequency = <400000>;
199 pinctrl-names = "default";
200 pinctrl-0 = <&pinctrl_i2c3>;
205 clock-frequency = <400000>;
206 pinctrl-names = "default";
207 pinctrl-0 = <&pinctrl_i2c4>;
218 pinctrl-names = "default";
219 pinctrl-0 = <&pinctrl_uart2>;
225 pinctrl-names = "default", "state_100mhz", "state_200mhz";
226 pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
227 pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
228 pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
229 cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
230 vmmc-supply = <®_usdhc2_vmmc>;
231 bus-width = <4>;
237 assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
238 assigned-clock-rates = <400000000>;
239 pinctrl-names = "default", "state_100mhz", "state_200mhz";
240 pinctrl-0 = <&pinctrl_usdhc3>;
241 pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
242 pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
243 bus-width = <8>;
244 non-removable;
249 pinctrl-names = "default";
250 pinctrl-0 = <&pinctrl_wdog>;
251 fsl,ext-reset-output;
341 pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
353 pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
387 pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
403 pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {