Lines Matching +full:mac +full:- +full:divider
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/linux-event-codes.h>
10 #include <dt-bindings/leds/common.h>
11 #include <dt-bindings/net/ti-dp83867.h>
17 compatible = "gw,imx8mn-gw7902", "fsl,imx8mn";
24 stdout-path = &uart2;
33 compatible = "fixed-clock";
34 #clock-cells = <0>;
35 clock-frequency = <20000000>;
36 clock-output-names = "can20m";
39 gpio-keys {
40 compatible = "gpio-keys";
42 key-user-pb {
48 key-user-pb1x {
51 interrupt-parent = <&gsc>;
55 key-erased {
58 interrupt-parent = <&gsc>;
62 key-eeprom-wp {
65 interrupt-parent = <&gsc>;
69 key-tamper {
72 interrupt-parent = <&gsc>;
76 switch-hold {
79 interrupt-parent = <&gsc>;
84 led-controller {
85 compatible = "gpio-leds";
86 pinctrl-names = "default";
87 pinctrl-0 = <&pinctrl_gpio_leds>;
89 led-0 {
94 default-state = "off";
97 led-1 {
102 default-state = "off";
105 led-2 {
110 default-state = "off";
113 led-3 {
118 default-state = "off";
121 led-4 {
126 default-state = "off";
131 compatible = "pps-gpio";
132 pinctrl-names = "default";
133 pinctrl-0 = <&pinctrl_pps>;
138 reg_3p3v: regulator-3p3v {
139 compatible = "regulator-fixed";
140 regulator-name = "3P3V";
141 regulator-min-microvolt = <3300000>;
142 regulator-max-microvolt = <3300000>;
143 regulator-always-on;
146 reg_usb1_vbus: regulator-usb1 {
147 compatible = "regulator-fixed";
148 pinctrl-names = "default";
149 pinctrl-0 = <&pinctrl_reg_usb1>;
150 regulator-name = "usb_usb1_vbus";
152 enable-active-high;
153 regulator-min-microvolt = <5000000>;
154 regulator-max-microvolt = <5000000>;
157 reg_wifi: regulator-wifi {
158 compatible = "regulator-fixed";
159 pinctrl-names = "default";
160 pinctrl-0 = <&pinctrl_reg_wl>;
161 regulator-name = "wifi";
163 enable-active-high;
164 startup-delay-us = <100>;
165 regulator-min-microvolt = <3300000>;
166 regulator-max-microvolt = <3300000>;
171 cpu-supply = <&buck2>;
175 cpu-supply = <&buck2>;
179 cpu-supply = <&buck2>;
183 cpu-supply = <&buck2>;
187 operating-points-v2 = <&ddrc_opp_table>;
189 ddrc_opp_table: opp-table {
190 compatible = "operating-points-v2";
192 opp-25000000 {
193 opp-hz = /bits/ 64 <25000000>;
196 opp-100000000 {
197 opp-hz = /bits/ 64 <100000000>;
200 opp-750000000 {
201 opp-hz = /bits/ 64 <750000000>;
207 pinctrl-names = "default";
208 pinctrl-0 = <&pinctrl_spi1>;
209 cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
216 interrupt-parent = <&gpio2>;
218 spi-max-frequency = <10000000>;
226 /* off-board header */
228 pinctrl-names = "default";
229 pinctrl-0 = <&pinctrl_spi2>;
230 cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
235 pinctrl-names = "default";
236 pinctrl-0 = <&pinctrl_fec1>;
237 phy-mode = "rgmii-id";
238 phy-handle = <ðphy0>;
239 local-mac-address = [00 00 00 00 00 00];
243 #address-cells = <1>;
244 #size-cells = <0>;
246 ethphy0: ethernet-phy@0 {
247 compatible = "ethernet-phy-ieee802.3-c22";
249 ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
250 ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
251 tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
252 rx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
258 gpio-line-names = "", "", "", "", "", "", "", "",
265 gpio-line-names = "", "", "", "", "", "", "", "",
272 gpio-line-names = "", "m2_gdis#", "", "", "", "", "", "m2_off#",
279 gpio-line-names = "", "", "", "", "", "", "", "",
287 gpio-line-names = "", "", "", "mipi_gpio4",
299 clock-frequency = <100000>;
300 pinctrl-names = "default", "gpio";
301 pinctrl-0 = <&pinctrl_i2c1>;
302 pinctrl-1 = <&pinctrl_i2c1_gpio>;
303 scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
304 sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
310 pinctrl-0 = <&pinctrl_gsc>;
311 interrupt-parent = <&gpio2>;
313 interrupt-controller;
314 #interrupt-cells = <1>;
315 #address-cells = <1>;
316 #size-cells = <0>;
319 compatible = "gw,gsc-adc";
320 #address-cells = <1>;
321 #size-cells = <0>;
339 gw,voltage-divider-ohms = <22100 1000>;
340 gw,voltage-offset-microvolt = <700000>;
347 gw,voltage-divider-ohms = <10000 10000>;
354 gw,voltage-divider-ohms = <10000 10000>;
397 gw,voltage-divider-ohms = <10000 10000>;
404 gw,voltage-divider-ohms = <10000 10000>;
411 gw,voltage-divider-ohms = <10000 10000>;
419 gpio-controller;
420 #gpio-cells = <2>;
421 interrupt-parent = <&gsc>;
428 pinctrl-names = "default";
429 pinctrl-0 = <&pinctrl_pmic>;
430 interrupt-parent = <&gpio3>;
432 rohm,reset-snvs-powered;
433 #clock-cells = <0>;
435 clock-output-names = "clk-32k-out";
438 /* vdd_soc: 0.805-0.900V (typ=0.8V) */
440 regulator-name = "buck1";
441 regulator-min-microvolt = <700000>;
442 regulator-max-microvolt = <1300000>;
443 regulator-boot-on;
444 regulator-always-on;
445 regulator-ramp-delay = <1250>;
448 /* vdd_arm: 0.805-1.0V (typ=0.9V) */
450 regulator-name = "buck2";
451 regulator-min-microvolt = <700000>;
452 regulator-max-microvolt = <1300000>;
453 regulator-boot-on;
454 regulator-always-on;
455 regulator-ramp-delay = <1250>;
456 rohm,dvs-run-voltage = <1000000>;
457 rohm,dvs-idle-voltage = <900000>;
460 /* vdd_0p9: 0.805-1.0V (typ=0.9V) */
462 regulator-name = "buck3";
463 regulator-min-microvolt = <700000>;
464 regulator-max-microvolt = <1350000>;
465 regulator-boot-on;
466 regulator-always-on;
471 regulator-name = "buck4";
472 regulator-min-microvolt = <3000000>;
473 regulator-max-microvolt = <3300000>;
474 regulator-boot-on;
475 regulator-always-on;
480 regulator-name = "buck5";
481 regulator-min-microvolt = <1605000>;
482 regulator-max-microvolt = <1995000>;
483 regulator-boot-on;
484 regulator-always-on;
489 regulator-name = "buck6";
490 regulator-min-microvolt = <800000>;
491 regulator-max-microvolt = <1400000>;
492 regulator-boot-on;
493 regulator-always-on;
498 regulator-name = "ldo1";
499 regulator-min-microvolt = <1600000>;
500 regulator-max-microvolt = <1900000>;
501 regulator-boot-on;
502 regulator-always-on;
507 regulator-name = "ldo2";
508 regulator-min-microvolt = <800000>;
509 regulator-max-microvolt = <900000>;
510 regulator-boot-on;
511 regulator-always-on;
516 regulator-name = "ldo3";
517 regulator-min-microvolt = <1800000>;
518 regulator-max-microvolt = <3300000>;
519 regulator-boot-on;
520 regulator-always-on;
524 regulator-name = "ldo4";
525 regulator-min-microvolt = <900000>;
526 regulator-max-microvolt = <1800000>;
527 regulator-boot-on;
528 regulator-always-on;
532 regulator-name = "ldo6";
533 regulator-min-microvolt = <900000>;
534 regulator-max-microvolt = <1800000>;
535 regulator-boot-on;
536 regulator-always-on;
572 clock-frequency = <400000>;
573 pinctrl-names = "default", "gpio";
574 pinctrl-0 = <&pinctrl_i2c2>;
575 pinctrl-1 = <&pinctrl_i2c2_gpio>;
576 scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
577 sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
582 pinctrl-names = "default";
583 pinctrl-0 = <&pinctrl_accel>;
585 st,drdy-int-pin = <1>;
586 interrupt-parent = <&gpio1>;
591 /* off-board header */
593 clock-frequency = <400000>;
594 pinctrl-names = "default", "gpio";
595 pinctrl-0 = <&pinctrl_i2c3>;
596 pinctrl-1 = <&pinctrl_i2c3_gpio>;
597 scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
598 sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
602 /* off-board header */
604 clock-frequency = <400000>;
605 pinctrl-names = "default", "gpio";
606 pinctrl-0 = <&pinctrl_i2c4>;
607 pinctrl-1 = <&pinctrl_i2c4_gpio>;
608 scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
609 sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
617 /* off-board header */
619 pinctrl-names = "default";
620 pinctrl-0 = <&pinctrl_sai3>;
621 assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
622 assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
623 assigned-clock-rates = <24576000>;
629 pinctrl-names = "default";
630 pinctrl-0 = <&pinctrl_uart1>, <&pinctrl_uart1_gpio>;
636 pinctrl-names = "default";
637 pinctrl-0 = <&pinctrl_uart2>;
643 pinctrl-names = "default";
644 pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_uart3_gpio>;
645 rts-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
646 cts-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
650 compatible = "brcm,bcm4330-bt";
651 shutdown-gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
657 pinctrl-names = "default";
658 pinctrl-0 = <&pinctrl_uart4>;
664 vbus-supply = <®_usb1_vbus>;
665 disable-over-current;
671 pinctrl-names = "default", "state_100mhz", "state_200mhz";
672 pinctrl-0 = <&pinctrl_usdhc2>;
673 pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
674 pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
675 bus-width = <4>;
676 non-removable;
677 vmmc-supply = <®_wifi>;
678 #address-cells = <1>;
679 #size-cells = <0>;
683 compatible = "brcm,bcm43455-fmac", "brcm,bcm4329-fmac";
690 pinctrl-names = "default", "state_100mhz", "state_200mhz";
691 pinctrl-0 = <&pinctrl_usdhc3>;
692 pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
693 pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
694 bus-width = <8>;
695 non-removable;
700 pinctrl-names = "default";
701 pinctrl-0 = <&pinctrl_wdog>;
702 fsl,ext-reset-output;
707 pinctrl-names = "default";
708 pinctrl-0 = <&pinctrl_hog>;
936 pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
947 pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
974 pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
990 pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {