dts/freescale/imx8mm-tqma8mqml-mba8mx.dts

1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
3  * Copyright 2020-2021 TQ-Systems GmbH
6 /dts-v1/;
8 #include <dt-bindings/phy/phy-imx8-pcie.h>
10 #include "imx8mm-tqma8mqml.dtsi"
14 	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
15 	compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
16 	chassis-type = "embedded";
27 	reg_usdhc2_vmmc: regulator-vmmc {
28 		compatible = "regulator-fixed";
29 		pinctrl-names = "default";
30 		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
31 		regulator-name = "VSD_3V3";
32 		regulator-min-microvolt = <3300000>;
33 		regulator-max-microvolt = <3300000>;
35 		enable-active-high;
36 		startup-delay-us = <100>;
37 		off-on-delay-us = <12000>;
41 		compatible = "gpio-usb-b-connector", "usb-b-connector";
44 		pinctrl-names = "default";
45 		pinctrl-0 = <&pinctrl_usb1_connector>;
46 		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
49 			#address-cells = <1>;
50 			#size-cells = <0>;
55 					remote-endpoint = <&usb1_drd_sw>;
66 		gpio-controller;
67 		#gpio-cells = <2>;
68 		vcc-supply = <&reg_vcc_3v3>;
69 		pinctrl-names = "default";
70 		pinctrl-0 = <&pinctrl_expander>;
71 		interrupt-parent = <&gpio1>;
73 		interrupt-controller;
74 		#interrupt-cells = <2>;
79 	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
80 	fsl,clkreq-unsupported;
82 	clock-names = "ref";
88 	reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
91 	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
93 	assigned-clock-rates = <10000000>, <250000000>;
94 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
100 	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
101 	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
102 	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
110 	clock-names = "mclk";
115 	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
116 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
120 	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
121 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
125 	pinctrl-names = "default";
126 	pinctrl-0 = <&pinctrl_usbotg1>;
128 	srp-disable;
129 	hnp-disable;
130 	adp-disable;
131 	power-active-high;
132 	over-current-active-low;
133 	usb-role-switch;
138 			remote-endpoint = <&usb_dr_connector>;
145 	disable-over-current;
146 	vbus-supply = <&reg_hub_vbus>;
260 	pinctrl_usb1_connector: usb1-connectorgrp {
278 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
288 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {