Lines Matching +full:fixed +full:- +full:header
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include "meson-gxbb.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/sound/meson-aiu.h>
13 compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
22 stdout-path = "serial0:115200n8";
31 compatible = "gpio-leds";
33 led-stat {
34 label = "nanopi-k2:blue:stat";
36 default-state = "on";
37 panic-indicator;
41 vdd_5v: regulator-vdd-5v {
42 compatible = "regulator-fixed";
43 regulator-name = "VDD_5V";
44 regulator-min-microvolt = <5000000>;
45 regulator-max-microvolt = <5000000>;
48 vddio_ao18: regulator-vddio-ao18 {
49 compatible = "regulator-fixed";
50 regulator-name = "VDDIO_AO18";
51 regulator-min-microvolt = <1800000>;
52 regulator-max-microvolt = <1800000>;
55 vddio_ao3v3: regulator-vddio-ao3v3 {
56 compatible = "regulator-fixed";
57 regulator-name = "VDDIO_AO3.3V";
58 regulator-min-microvolt = <3300000>;
59 regulator-max-microvolt = <3300000>;
62 vddio_tf: regulator-vddio-tf {
63 compatible = "regulator-gpio";
65 regulator-name = "VDDIO_TF";
66 regulator-min-microvolt = <1800000>;
67 regulator-max-microvolt = <3300000>;
70 gpios-states = <0>;
75 regulator-settling-time-up-us = <100>;
76 regulator-settling-time-down-us = <5000>;
79 wifi_32k: wifi-32k {
80 compatible = "pwm-clock";
81 #clock-cells = <0>;
82 clock-frequency = <32768>;
86 sdio_pwrseq: sdio-pwrseq {
87 compatible = "mmc-pwrseq-simple";
88 reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
90 clock-names = "ext_clock";
93 vcc1v8: regulator-vcc1v8 {
94 compatible = "regulator-fixed";
95 regulator-name = "VCC1.8V";
96 regulator-min-microvolt = <1800000>;
97 regulator-max-microvolt = <1800000>;
100 vcc3v3: regulator-vcc3v3 {
101 compatible = "regulator-fixed";
102 regulator-name = "VCC3.3V";
103 regulator-min-microvolt = <3300000>;
104 regulator-max-microvolt = <3300000>;
107 emmc_pwrseq: emmc-pwrseq {
108 compatible = "mmc-pwrseq-emmc";
109 reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
113 cvbs-connector {
114 compatible = "composite-video-connector";
119 remote-endpoint = <&cvbs_vdac_out>;
124 hdmi-connector {
125 compatible = "hdmi-connector";
130 remote-endpoint = <&hdmi_tx_tmds_out>;
136 compatible = "amlogic,gx-sound-card";
137 model = "NANOPI-K2";
142 assigned-clocks = <&clkc CLKID_MPLL0>,
145 assigned-clock-parents = <0>, <0>, <0>;
146 assigned-clock-rates = <294912000>,
150 dai-link-0 {
151 sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
154 dai-link-1 {
155 sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
156 dai-format = "i2s";
157 mclk-fs = <256>;
159 codec-0 {
160 sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
164 dai-link-2 {
165 sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
167 codec-0 {
168 sound-dai = <&hdmi_tx>;
180 pinctrl-0 = <&ao_cec_pins>;
181 pinctrl-names = "default";
182 hdmi-phandle = <&hdmi_tx>;
187 remote-endpoint = <&cvbs_connector_in>;
193 pinctrl-0 = <ð_rgmii_pins>;
194 pinctrl-names = "default";
196 phy-handle = <ð_phy0>;
197 phy-mode = "rgmii";
199 amlogic,tx-delay-ns = <2>;
202 compatible = "snps,dwmac-mdio";
203 #address-cells = <1>;
204 #size-cells = <0>;
206 eth_phy0: ethernet-phy@0 {
210 reset-assert-us = <10000>;
211 reset-deassert-us = <80000>;
212 reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
214 interrupt-parent = <&gpio_intc>;
223 pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
224 pinctrl-names = "default";
229 remote-endpoint = <&hdmi_connector_in>;
235 pinctrl-0 = <&remote_input_ao_pins>;
236 pinctrl-names = "default";
240 gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
241 "VCCK En", "CON1 Header Pin31",
242 "I2S Header Pin6", "IR In", "I2S Header Pin7",
243 "I2S Header Pin3", "I2S Header Pin4",
244 "I2S Header Pin5", "HDMI CEC", "SYS LED",
250 gpio-line-names = /* Bank GPIOZ */
258 "CON1 Header Pin33",
274 "CON1 Header Pin7", "CON1 Header Pin11",
275 "CON1 Header Pin13", "CON1 Header Pin15",
276 "CON1 Header Pin18", "CON1 Header Pin19",
277 "CON1 Header Pin22", "CON1 Header Pin21",
278 "CON1 Header Pin24", "CON1 Header Pin23",
279 "CON1 Header Pin26", "CON1 Header Pin29",
280 "CON1 Header Pin32", "CON1 Header Pin8",
281 "CON1 Header Pin10", "CON1 Header Pin16",
282 "CON1 Header Pin12",
294 "", "CON1 Header Pin35", "", "";
299 pinctrl-0 = <&pwm_e_pins>;
300 pinctrl-names = "default";
302 clock-names = "clkin0";
307 vref-supply = <&vddio_ao18>;
313 pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
314 pinctrl-1 = <&sdio_clk_gate_pins>;
315 pinctrl-names = "default", "clk-gate";
316 #address-cells = <1>;
317 #size-cells = <0>;
319 bus-width = <4>;
320 cap-sd-highspeed;
321 max-frequency = <50000000>;
323 non-removable;
324 disable-wp;
327 keep-power-in-suspend;
329 mmc-pwrseq = <&sdio_pwrseq>;
331 vmmc-supply = <&vddio_ao3v3>;
332 vqmmc-supply = <&vddio_ao18>;
335 compatible = "brcm,bcm4329-fmac";
343 pinctrl-0 = <&sdcard_pins>;
344 pinctrl-1 = <&sdcard_clk_gate_pins>;
345 pinctrl-names = "default", "clk-gate";
347 bus-width = <4>;
348 cap-sd-highspeed;
349 sd-uhs-sdr12;
350 sd-uhs-sdr25;
351 sd-uhs-sdr50;
352 sd-uhs-ddr50;
353 max-frequency = <100000000>;
354 disable-wp;
356 cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
358 vmmc-supply = <&vddio_ao3v3>;
359 vqmmc-supply = <&vddio_tf>;
365 pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
366 pinctrl-1 = <&emmc_clk_gate_pins>;
367 pinctrl-names = "default", "clk-gate";
369 bus-width = <8>;
370 max-frequency = <200000000>;
371 non-removable;
372 disable-wp;
373 cap-mmc-highspeed;
374 mmc-ddr-1_8v;
375 mmc-hs200-1_8v;
377 mmc-pwrseq = <&emmc_pwrseq>;
378 vmmc-supply = <&vcc3v3>;
379 vqmmc-supply = <&vcc1v8>;
385 pinctrl-0 = <&uart_ao_a_pins>;
386 pinctrl-names = "default";
392 pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
393 pinctrl-names = "default";
394 uart-has-rtscts;
397 compatible = "brcm,bcm43438-bt";
399 clock-names = "lpo";
400 vbat-supply = <&vddio_ao3v3>;
401 vddio-supply = <&vddio_ao18>;
402 host-wakeup-gpios = <&gpio GPIOX_21 GPIO_ACTIVE_HIGH>;
403 shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
407 /* 40-pin CON1 */
410 pinctrl-0 = <&uart_c_pins>;
411 pinctrl-names = "default";
416 phy-supply = <&vdd_5v>;