ti/omap/omap3-beagle-xm.dts

1 // SPDX-License-Identifier: GPL-2.0-only
3  * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
5 /dts-v1/;
11 	compatible = "ti,omap3-beagle-xm", "ti,omap3630", "ti,omap3";
15 			cpu0-supply = <&vcc>;
32 		#clock-cells = <0>;
33 		compatible = "fixed-clock";
34 		clock-frequency = <26000000>;
37 	led-controller-1 {
38 		compatible = "gpio-leds";
40 		led-1 {
42 			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */
43 			linux,default-trigger = "heartbeat";
46 		led-2 {
48 			gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */
49 			linux,default-trigger = "mmc0";
53 	led-controller-2 {
54 		compatible = "pwm-leds";
56 		led-3 {
59 			max-brightness = <127>;
64 		compatible = "ti,omap-twl4030";
71 		compatible = "gpio-keys";
77 			wakeup-source;
82 	/* HS USB Port 2 Power */
84 		compatible = "regulator-fixed";
85 		regulator-name = "hsusb2_vbus";
86 		regulator-min-microvolt = <3300000>;
87 		regulator-max-microvolt = <3300000>;
89 		startup-delay-us = <70000>;
92 	/* HS USB Host PHY on PORT 2 */
93 	hsusb2_phy: hsusb2-phy-pins {
94 		compatible = "usb-nop-xceiv";
95 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
96 		vcc-supply = <&hsusb2_power>;
97 		#phy-cells = <0>;
102 		powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
107 			#address-cells = <1>;
108 			#size-cells = <0>;
110 			port@0 {
114 					remote-endpoint = <&dpi_out>;
118 			port@1 {
122 					remote-endpoint = <&dvi_connector_in>;
129 		compatible = "dvi-connector";
134 		ddc-i2c-bus = <&i2c3>;
136 		port {
138 				remote-endpoint = <&tfp410_out>;
144 		compatible = "svideo-connector";
147 		port {
149 				remote-endpoint = <&venc_out>;
155 		compatible = "arm,coresight-etb10", "arm,primecell";
159 		clock-names = "apb_pclk";
160 		in-ports {
161 			port {
163 					remote-endpoint = <&etm_out>;
170 		compatible = "arm,coresight-etm3x", "arm,primecell";
174 		clock-names = "apb_pclk";
175 		out-ports {
176 			port {
178 					remote-endpoint = <&etb_in>;
186 	gpio1_pins: gpio1-pins {
187 		pinctrl-single,pins = <
192 	dss_dpi_pins2: dss-dpi1-pins {
193 		pinctrl-single,pins = <
205 	pinctrl-names = "default";
206 	pinctrl-0 = <
210 	uart3_pins: uart3-pins {
211 		pinctrl-single,pins = <
217 	hsusb2_pins: hsusb2-pins {
218 		pinctrl-single,pins = <
228 	dss_dpi_pins1: dss-dpi2-pins {
229 		pinctrl-single,pins = <
259 	pinctrl-names = "default";
260 	pinctrl-0 = <
264 	hsusb2_2_pins: hsusb2-2-pins {
265 		pinctrl-single,pins = <
277 	clock-frequency = <2600000>;
282 		interrupt-parent = <&intc>;
285 		clock-names = "fck";
288 			compatible = "ti,twl4030-audio";
294 			compatible = "ti,twl4030-power-beagleboard-xm", "ti,twl4030-power-idle-osc-off";
304 	clock-frequency = <400000>;
308 	clock-frequency = <100000>;
312 	vmmc-supply = <&vmmc1>;
313 	vqmmc-supply = <&vsim>;
314 	bus-width = <8>;
326 	ti,use-leds;
338 	interface-type = <0>;
339 	usb-phy = <&usb2_phy>;
341 	phy-names = "usb2-phy";
347 	interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
348 	pinctrl-names = "default";
349 	pinctrl-0 = <&uart3_pins>;
353 	pinctrl-names = "default";
354 	pinctrl-0 = <&gpio1_pins>;
358 	port2-mode = "ehci-phy";
364 	#address-cells = <1>;
365 	#size-cells = <0>;
370 		#address-cells = <1>;
371 		#size-cells = <0>;
381 	regulator-name = "usb_1v8";
382 	regulator-min-microvolt = <1800000>;
383 	regulator-max-microvolt = <1800000>;
384 	regulator-always-on;
394 	pinctrl-names = "default";
395 	pinctrl-0 = <
400 	port {
402 			remote-endpoint = <&tfp410_in>;
403 			data-lines = <24>;
411 	vdda-supply = <&vdac>;
413 	port {
415 			remote-endpoint = <&tv_connector_in>;