dts/st/ste-hrefv60plus.dtsi

1 // SPDX-License-Identifier: GPL-2.0-or-later
3  * Copyright 2012 ST-Ericsson AB
6 #include "ste-href.dtsi"
9 	model = "ST-Ericsson HREF (v60+) platform with Device Tree";
10 	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
12 	thermal-zones {
13 		chassis-thermal {
15 			polling-delay = <20000>;
17 			polling-delay-passive = <2000>;
19 			thermal-sensors = <&therm1>, <&therm2>;
23 				chassis_alert: chassis-alert {
29 				chassis_crit: chassis-crit {
38 			cooling-maps {
41 					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
54 		io-channels = <&gpadc 0x06>; /* AUX1 */
55 		pullup-uv = <1800000>;
56 		pullup-ohm = <220000>;
57 		pulldown-ohm = <0>;
58 		#thermal-sensor-cells = <0>;
63 		io-channels = <&gpadc 0x07>; /* AUX2 */
64 		pullup-uv = <1800000>;
65 		pullup-ohm = <220000>;
66 		pulldown-ohm = <0>;
67 		#thermal-sensor-cells = <0>;
71 		/* Name the GPIO muxed rails on the HREF boards */
72 		gpio@8012e000 {
73 			/* GPIOs 0 - 31 */
74 			gpio-line-names =
94 		gpio@8012e080 {
95 			/* GPIOs 32 - 63 */
96 			gpio-line-names =
104 		gpio@8000e000 {
105 			/* GPIOs 64 - 95 */
106 			gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
112 				     /* GPIO 70-77 used for ETM */
114 				     /* GPIO 78-81 used for YCBCR */
127 		gpio@8000e080 {
128 			/* GPIOs 96 - 127 */
129 			gpio-line-names = "",
137 		gpio@8000e100 {
138 			/* GPIOs 128 - 159 */
139 			gpio-line-names = "", "", "", "", "", "", "", "",
154 		gpio@8000e180 {
155 			/* GPIOs 160 - 191 */
156 			gpio-line-names = "", "", "", "", "", "", "", "",
166 		gpio@8011e000 {
167 			/* GPIOs 192 - 223 */
168 			gpio-line-names = "HDTV_INTN",
174 				     /* GPIO208-216 used for WGBF_MC1 */
181 		gpio@8011e080 {
182 			/* GPIOs 224 - 255 */
183 			gpio-line-names = "", "",
193 			cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
201 			pinctrl-names = "default";
202 			pinctrl-0 = <&ipgpio_hrefv60_mode>,
215 					/* SD card detect GPIO pin, extend default state */
224 				 * XENON Flashgun on image processor GPIO (controlled from image
225 				 * processor firmware), mux in these image processor GPIO lines 0
227 				 * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
251 				 * Drive D19-D23 for the ETM PTM trace interface low,
282 					/* NFC ENA and RESET to low, pulldown IRQ line */
319 					/* Audio Amplifier HF enable GPIO */
329 					 * GBF (GPS, Bluetooth, FM-radio) interface,
330 					 * pull low to reset state
340 					/* MSP : HDTV INTERFACE GPIO line */
350 					 * Display Interface 1 uses GPIO 65 for RST (reset).
351 					 * Display Interface 2 uses GPIO 66 for RST (reset).
352 					 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
365 				/* Dangling GPIO pins */