Lines Matching +full:gain +full:- +full:gpios
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
7 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
16 stdout-path = &uart4;
29 clock_ksz8081: clock-ksz8081 {
30 compatible = "fixed-clock";
31 #clock-cells = <0>;
32 clock-frequency = <50000000>;
35 clock_ksz9031: clock-ksz9031 {
36 compatible = "fixed-clock";
37 #clock-cells = <0>;
38 clock-frequency = <25000000>;
41 clock_mcp251xfd: clock-mcp251xfd {
42 compatible = "fixed-clock";
43 #clock-cells = <0>;
44 clock-frequency = <20000000>;
47 clock_sja1105: clock-sja1105 {
48 compatible = "fixed-clock";
49 #clock-cells = <0>;
50 clock-frequency = <25000000>;
54 compatible = "virtual,mdio-gpio";
55 pinctrl-names = "default";
56 pinctrl-0 = <&pinctrl_mdio>;
58 #address-cells = <1>;
59 #size-cells = <0>;
60 gpios = <&gpio5 6 GPIO_ACTIVE_HIGH
64 usbeth_phy: ethernet-phy@3 {
67 interrupts-extended = <&gpio5 12 IRQ_TYPE_LEVEL_LOW>;
68 reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
69 reset-assert-us = <500>;
70 reset-deassert-us = <1000>;
72 clock-names = "rmii-ref";
73 micrel,led-mode = <0>;
76 tja1102_phy0: ethernet-phy@4 {
79 interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
80 reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
81 reset-assert-us = <20>;
82 reset-deassert-us = <2000>;
83 #address-cells = <1>;
84 #size-cells = <0>;
86 tja1102_phy1: ethernet-phy@5 {
89 interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
94 reg_5v0: regulator-5v0 {
95 compatible = "regulator-fixed";
96 regulator-name = "5v0";
97 regulator-min-microvolt = <5000000>;
98 regulator-max-microvolt = <5000000>;
101 reg_otg_vbus: regulator-otg-vbus {
102 compatible = "regulator-fixed";
103 regulator-name = "otg-vbus";
104 regulator-min-microvolt = <5000000>;
105 regulator-max-microvolt = <5000000>;
107 enable-active-high;
110 usdhc2_wifi_pwrseq: usdhc2-wifi-pwrseq {
111 compatible = "mmc-pwrseq-simple";
112 pinctrl-names = "default";
113 pinctrl-0 = <&pinctrl_wifi_npd>;
114 reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
119 pinctrl-names = "default";
120 pinctrl-0 = <&pinctrl_can1>;
121 xceiver-supply = <®_5v0>;
126 cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
127 pinctrl-names = "default";
128 pinctrl-0 = <&pinctrl_ecspi2>;
134 spi-max-frequency = <4000000>;
135 spi-rx-delay-us = <1>;
136 spi-tx-delay-us = <1>;
137 spi-cpha;
139 reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
144 #address-cells = <1>;
145 #size-cells = <0>;
150 phy-handle = <&usbeth_phy>;
151 phy-mode = "rmii";
157 phy-handle = <&tja1102_phy1>;
158 phy-mode = "rmii";
164 phy-handle = <&tja1102_phy0>;
165 phy-mode = "rmii";
172 phy-handle = <&rgmii_phy>;
173 phy-mode = "rgmii-id";
180 phy-mode = "rgmii-id";
181 rx-internal-delay-ps = <2000>;
182 tx-internal-delay-ps = <2000>;
184 fixed-link {
186 full-duplex;
194 cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
195 pinctrl-names = "default";
196 pinctrl-0 = <&pinctrl_ecspi3>;
201 pinctrl-names = "default";
202 pinctrl-0 = <&pinctrl_can2>;
205 spi-max-frequency = <10000000>;
206 interrupts-extended = <&gpio4 25 IRQ_TYPE_LEVEL_LOW>;
211 pinctrl-names = "default";
212 pinctrl-0 = <&pinctrl_enet>;
213 assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF>;
214 assigned-clock-rates = <125000000>;
217 phy-mode = "rgmii";
219 fixed-link {
221 full-duplex;
225 #address-cells = <1>;
226 #size-cells = <0>;
229 rgmii_phy: ethernet-phy@2 {
232 interrupts-extended = <&gpio1 28 IRQ_TYPE_EDGE_FALLING>;
233 reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
234 reset-assert-us = <10000>;
235 reset-deassert-us = <1000>;
243 gpio-line-names =
251 gpio-line-names =
260 gpio-line-names =
268 gpio-line-names =
276 gpio-line-names =
287 gpio-line-names =
297 clock-frequency = <100000>;
298 pinctrl-names = "default";
299 pinctrl-0 = <&pinctrl_i2c1>;
309 #address-cells = <1>;
310 #size-cells = <0>;
315 ti,gain = <1>;
322 ti,gain = <1>;
329 ti,gain = <1>;
335 ti,gain = <1>;
342 pinctrl-names = "default";
343 pinctrl-0 = <&pinctrl_uart4>;
348 vbus-supply = <®_otg_vbus>;
349 pinctrl-names = "default";
350 pinctrl-0 = <&pinctrl_usbotg>;
353 over-current-active-low;
366 pinctrl-names = "default";
367 pinctrl-0 = <&pinctrl_usdhc1>;
368 cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
369 no-1-8-v;
370 disable-wp;
371 cap-sd-highspeed;
372 no-mmc;
373 no-sdio;
378 pinctrl-names = "default";
379 pinctrl-0 = <&pinctrl_usdhc2>;
380 no-1-8-v;
381 non-removable;
382 mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
384 #address-cells = <1>;
385 #size-cells = <0>;
389 compatible = "brcm,bcm4329-fmac";
394 pinctrl-names = "default";
395 pinctrl-0 = <&pinctrl_usdhc3>;
396 bus-width = <8>;
397 no-1-8-v;
398 non-removable;
399 no-sd;
400 no-sdio;
493 /* phy12/tja1102_phy0 enable. Set 100K pull-up */