Lines Matching +full:button +full:- +full:191
1 // SPDX-License-Identifier: GPL-2.0 OR MIT
6 // Copyright 2018-2021 General Electric Company
7 // Copyright 2018-2021 Collabora
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/sound/fsl-imx-audmux.h>
20 compatible = "regulator-fixed";
21 regulator-name = "3P3V";
22 regulator-min-microvolt = <3300000>;
23 regulator-max-microvolt = <3300000>;
27 compatible = "i2c-mux-gpio";
28 #address-cells = <1>;
29 #size-cells = <0>;
30 mux-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>;
31 i2c-parent = <&i2c2>;
35 #address-cells = <1>;
36 #size-cells = <0>;
41 #address-cells = <1>;
42 #size-cells = <0>;
48 pinctrl-names = "default";
49 pinctrl-0 = <&pinctrl_audmux>;
51 mux-ssi1 {
52 fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
53 fsl,port-config = <
63 mux-aud6 {
64 fsl,audmux-port = <MX51_AUDMUX_PORT6>;
65 fsl,port-config = <
74 clock-names = "ckil";
75 assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
77 assigned-clock-parents = <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
82 cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
83 pinctrl-names = "default";
84 pinctrl-0 = <&pinctrl_spi1>;
88 #address-cells = <1>;
89 #size-cells = <1>;
90 compatible = "sst,sst25vf032b", "jedec,spi-nor";
91 spi-max-frequency = <20000000>;
107 read-only;
113 pinctrl-names = "default";
114 pinctrl-0 = <&pinctrl_enet &pinctrl_phy_reset>;
115 phy-mode = "rgmii-id";
116 phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
117 fsl,magic-packet;
118 phy-handle = <&phy0>;
121 #address-cells = <1>;
122 #size-cells = <0>;
124 phy0: ethernet-phy@6 {
126 qca,clk-out-frequency = <125000000>;
132 clock-frequency = <100000>;
133 pinctrl-names = "default", "gpio";
134 pinctrl-0 = <&pinctrl_i2c1>;
135 pinctrl-1 = <&pinctrl_i2c1_gpio>;
136 scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
137 sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
142 clock-frequency = <100000>;
143 pinctrl-names = "default", "gpio";
144 pinctrl-0 = <&pinctrl_i2c2>;
145 pinctrl-1 = <&pinctrl_i2c2_gpio>;
146 scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
147 sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
152 clock-frequency = <100000>;
153 pinctrl-names = "default", "gpio";
154 pinctrl-0 = <&pinctrl_i2c3>;
155 pinctrl-1 = <&pinctrl_i2c3_gpio>;
156 scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
157 sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
165 compatible = "fixed-clock";
166 #clock-cells = <0>;
167 clock-frequency = <32768>;
179 regulator-min-microvolt = <300000>;
180 regulator-max-microvolt = <1875000>;
181 regulator-boot-on;
182 regulator-always-on;
183 regulator-ramp-delay = <6250>;
187 regulator-min-microvolt = <300000>;
188 regulator-max-microvolt = <1875000>;
189 regulator-boot-on;
190 regulator-always-on;
191 regulator-ramp-delay = <6250>;
195 regulator-min-microvolt = <800000>;
196 regulator-max-microvolt = <3300000>;
197 regulator-boot-on;
198 regulator-always-on;
202 regulator-min-microvolt = <400000>;
203 regulator-max-microvolt = <1975000>;
204 regulator-boot-on;
205 regulator-always-on;
209 regulator-min-microvolt = <400000>;
210 regulator-max-microvolt = <1975000>;
211 regulator-boot-on;
212 regulator-always-on;
216 regulator-min-microvolt = <675000>;
217 regulator-max-microvolt = <3300000>;
218 regulator-boot-on;
219 regulator-always-on;
223 regulator-min-microvolt = <5000000>;
224 regulator-max-microvolt = <5150000>;
228 regulator-min-microvolt = <1000000>;
229 regulator-max-microvolt = <3000000>;
230 regulator-boot-on;
231 regulator-always-on;
235 regulator-boot-on;
236 regulator-always-on;
241 * maintain backward compatibility with hw-rev. A.0
244 regulator-min-microvolt = <1800000>;
245 regulator-max-microvolt = <3300000>;
246 regulator-always-on;
250 regulator-min-microvolt = <2500000>;
251 regulator-max-microvolt = <2500000>;
252 regulator-always-on;
256 regulator-min-microvolt = <1800000>;
257 regulator-max-microvolt = <3300000>;
258 regulator-always-on;
263 regulator-min-microvolt = <1800000>;
264 regulator-max-microvolt = <1800000>;
265 regulator-boot-on;
266 regulator-always-on;
273 reset-gpio = <&gpio1 20 0>;
277 pinctrl-names = "default";
278 pinctrl-0 = <&pinctrl_pwm4>;
282 vin-supply = <&sw1a_reg>;
286 vin-supply = <&sw1c_reg>;
290 vin-supply = <&sw1c_reg>;
298 pinctrl-names = "default";
299 pinctrl-0 = <&pinctrl_uart2>;
304 pinctrl-names = "default";
305 pinctrl-0 = <&pinctrl_uart3>;
310 /* Connected to USB-Hub SMSC USB2514, provides P0, P2, P3, P4 on Qseven connector */
311 vbus-supply = <®_5v>;
316 pinctrl-names = "default";
317 pinctrl-0 = <&pinctrl_usbotg>;
322 pinctrl-names = "default";
323 pinctrl-0 = <&pinctrl_usdhc2>;
324 cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
325 no-1-8-v;
326 keep-power-in-suspend;
327 wakeup-source;
328 vmmc-supply = <®_3p3v>;
334 pinctrl-names = "default";
335 pinctrl-0 = <&pinctrl_usdhc3>;
336 non-removable;
337 bus-width = <8>;
338 no-1-8-v;
339 keep-power-in-suspend;
340 wakeup-source;
341 vmmc-supply = <®_3p3v>;
346 pinctrl-names = "default";
347 pinctrl-0 = <&pinctrl_wdog>;
348 fsl,ext-reset-output;
352 pinctrl-names = "default";
353 pinctrl-0 = <&pinctrl_hog>;
355 qmx6mux: imx6qdl-qmx6 {
365 /* PHY is on System on Module, Q7[3-15] have Ethernet lines */
404 pinctrl_i2c1_gpio: i2c1-gpio {
418 pinctrl_i2c2_gpio: i2c2-gpio {
432 pinctrl_i2c3_gpio: i2c3-gpio {
439 pinctrl_phy_reset: phy-reset {
451 pinctrl_q7_backlight_enable: q7-backlight-enable {
457 pinctrl_q7_gpio0: q7-gpio0 {
463 pinctrl_q7_gpio1: q7-gpio1 {
469 pinctrl_q7_gpio2: q7-gpio2 {
475 pinctrl_q7_gpio3: q7-gpio3 {
481 pinctrl_q7_gpio4: q7-gpio4 {
487 pinctrl_q7_gpio5: q7-gpio5 {
493 pinctrl_q7_gpio6: q7-gpio6 {
495 MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x1b0b0 /* Q7[191] GPIO6 */
499 pinctrl_q7_gpio7: q7-gpio7 {
505 pinctrl_q7_hda_reset: q7-hda-reset {
511 pinctrl_q7_lcd_power: lcd-power {
517 pinctrl_q7_sdio_power: q7-sdio-power {
523 pinctrl_q7_sleep_button: q7-sleep-button {
529 pinctrl_q7_spi_cs1: spi-cs1 {