Lines Matching +full:y +full:- +full:plate +full:- +full:ohms
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
7 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/leds/common.h>
17 stdout-path = &uart4;
21 compatible = "pwm-backlight";
23 brightness-levels = <0 1000>;
24 num-interpolated-steps = <20>;
25 default-brightness-level = <19>;
26 power-supply = <®_12v0>;
30 compatible = "fsl,imx-parallel-display";
31 pinctrl-0 = <&pinctrl_ipu1_disp>;
32 pinctrl-names = "default";
33 #address-cells = <1>;
34 #size-cells = <0>;
40 remote-endpoint = <&ipu1_di0_disp0>;
48 remote-endpoint = <&panel_in>;
53 iio-hwmon {
54 compatible = "iio-hwmon";
55 io-channels = <&vdiv_vaccu>;
59 compatible = "gpio-leds";
60 pinctrl-names = "default";
61 pinctrl-0 = <&pinctrl_leds>;
63 led-0 {
67 linux,default-trigger = "heartbeat";
74 power-supply = <®_3v3>;
78 remote-endpoint = <&display_out>;
83 clk50m_phy: phy-clock {
84 compatible = "fixed-clock";
85 #clock-cells = <0>;
86 clock-frequency = <50000000>;
87 clock-output-names = "enet_ref_pad";
90 reg_3v3: regulator-3v3 {
91 compatible = "regulator-fixed";
92 regulator-name = "3v3";
93 regulator-min-microvolt = <3300000>;
94 regulator-max-microvolt = <3300000>;
97 reg_5v0: regulator-5v0 {
98 compatible = "regulator-fixed";
99 regulator-name = "5v0";
100 regulator-min-microvolt = <5000000>;
101 regulator-max-microvolt = <5000000>;
104 reg_12v0: regulator-12v0 {
105 compatible = "regulator-fixed";
106 regulator-name = "12v0";
107 regulator-min-microvolt = <12000000>;
108 regulator-max-microvolt = <12000000>;
111 thermal-zones {
112 chassis-thermal {
113 polling-delay = <20000>;
114 polling-delay-passive = <0>;
115 thermal-sensors = <&tsens0>;
126 touch-thermal0 {
127 polling-delay = <20000>;
128 polling-delay-passive = <0>;
129 thermal-sensors = <&touch_temp0>;
140 touch-thermal1 {
141 polling-delay = <20000>;
142 polling-delay-passive = <0>;
143 thermal-sensors = <&touch_temp1>;
156 compatible = "resistive-adc-touch";
157 io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
159 io-channel-names = "y", "z1", "z2", "x";
160 touchscreen-min-pressure = <64687>;
161 touchscreen-inverted-x;
162 touchscreen-inverted-y;
163 touchscreen-x-plate-ohms = <300>;
164 touchscreen-y-plate-ohms = <800>;
167 touch_temp0: touch-temperature-sensor0 {
168 compatible = "generic-adc-thermal";
169 #thermal-sensor-cells = <0>;
170 io-channels = <&adc_ts 0>;
171 io-channel-names = "sensor-channel";
172 temperature-lookup-table = < (-40000) 736
176 touch_temp1: touch-temperature-sensor1 {
177 compatible = "generic-adc-thermal";
178 #thermal-sensor-cells = <0>;
179 io-channels = <&adc_ts 7>;
180 io-channel-names = "sensor-channel";
181 temperature-lookup-table = < (-40000) 826
185 vdiv_vaccu: voltage-divider-vaccu {
186 compatible = "voltage-divider";
187 io-channels = <&adc_ts 2>;
188 output-ohms = <2500>;
189 full-ohms = <64000>;
190 #io-channel-cells = <0>;
195 pinctrl-names = "default";
196 pinctrl-0 = <&pinctrl_can1>;
197 xceiver-supply = <®_5v0>;
203 clock-names = "enet_ref_pad";
204 assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
205 assigned-clock-parents = <&clk50m_phy>;
209 cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
210 pinctrl-names = "default";
211 pinctrl-0 = <&pinctrl_ecspi1>;
215 compatible = "jedec,spi-nor";
217 spi-max-frequency = <20000000>;
222 cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
223 pinctrl-names = "default";
224 pinctrl-0 = <&pinctrl_ecspi2>;
228 compatible = "ti,tsc2046e-adc";
230 pinctrl-0 = <&pinctrl_tsc2046>;
231 pinctrl-names = "default";
232 spi-max-frequency = <1000000>;
233 interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
234 #io-channel-cells = <1>;
236 #address-cells = <1>;
237 #size-cells = <0>;
241 settling-time-us = <300>;
242 oversampling-ratio = <5>;
247 settling-time-us = <700>;
248 oversampling-ratio = <5>;
253 settling-time-us = <300>;
254 oversampling-ratio = <5>;
259 settling-time-us = <700>;
260 oversampling-ratio = <5>;
265 settling-time-us = <700>;
266 oversampling-ratio = <5>;
271 settling-time-us = <700>;
272 oversampling-ratio = <5>;
279 settling-time-us = <300>;
280 oversampling-ratio = <5>;
286 pinctrl-names = "default";
287 pinctrl-0 = <&pinctrl_enet>;
288 phy-mode = "rmii";
289 phy-handle = <&rgmii_phy>;
293 #address-cells = <1>;
294 #size-cells = <0>;
297 rgmii_phy: ethernet-phy@0 {
299 interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
300 reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
301 reset-assert-us = <10000>;
302 reset-deassert-us = <300>;
308 gpio-line-names =
316 gpio-line-names =
324 gpio-line-names =
332 gpio-line-names =
340 gpio-line-names =
348 clock-frequency = <100000>;
349 pinctrl-names = "default";
350 pinctrl-0 = <&pinctrl_i2c1>;
357 clock-frequency = <100000>;
358 pinctrl-names = "default";
359 pinctrl-0 = <&pinctrl_i2c3>;
362 tsens0: temperature-sensor@70 {
365 #thermal-sensor-cells = <0>;
370 remote-endpoint = <&display_in>;
374 pinctrl-names = "default";
375 pinctrl-0 = <&pinctrl_pwm1>;
380 pinctrl-names = "default";
381 pinctrl-0 = <&pinctrl_uart4>;
396 disable-over-current;
401 pinctrl-names = "default";
402 pinctrl-0 = <&pinctrl_usdhc1>;
403 cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
404 no-1-8-v;
405 disable-wp;
406 cap-sd-highspeed;
407 no-mmc;
408 no-sdio;
413 pinctrl-names = "default";
414 pinctrl-0 = <&pinctrl_usdhc3>;
415 bus-width = <8>;
416 no-1-8-v;
417 non-removable;
418 no-sd;
419 no-sdio;