Lines Matching +full:trickle +full:- +full:resistor +full:- +full:ohms
2 * Copyright 2012-2017 <LW@KARO-electronics.de>
3 * based on imx53-qsb.dts
7 * This file is dual-licensed: you can use it either under the terms
46 #include <dt-bindings/gpio/gpio.h>
49 model = "Ka-Ro electronics TX53 module";
62 reg-can-xcvr = ®_can_xcvr;
69 clock-frequency = <0>;
73 mclk: clock-mclk {
74 compatible = "fixed-clock";
75 #clock-cells = <0>;
76 clock-frequency = <26000000>;
79 gpio-keys {
80 compatible = "gpio-keys";
81 pinctrl-names = "default";
82 pinctrl-0 = <&pinctrl_gpio_key>;
84 key-power {
88 wakeup-source;
93 compatible = "gpio-leds";
94 pinctrl-names = "default";
95 pinctrl-0 = <&pinctrl_stk5led>;
97 led-user {
100 linux,default-trigger = "heartbeat";
104 reg_2v5: regulator-2v5 {
105 compatible = "regulator-fixed";
106 regulator-name = "2V5";
107 regulator-min-microvolt = <2500000>;
108 regulator-max-microvolt = <2500000>;
111 reg_3v3: regulator-3v3 {
112 compatible = "regulator-fixed";
113 regulator-name = "3V3";
114 regulator-min-microvolt = <3300000>;
115 regulator-max-microvolt = <3300000>;
118 reg_can_xcvr: regulator-can-xcvr {
119 compatible = "regulator-fixed";
120 regulator-name = "CAN XCVR";
121 regulator-min-microvolt = <3300000>;
122 regulator-max-microvolt = <3300000>;
123 pinctrl-names = "default";
124 pinctrl-0 = <&pinctrl_can_xcvr>;
128 reg_usbh1_vbus: regulator-usbh1-vbus {
129 compatible = "regulator-fixed";
130 regulator-name = "usbh1_vbus";
131 regulator-min-microvolt = <5000000>;
132 regulator-max-microvolt = <5000000>;
133 pinctrl-names = "default";
134 pinctrl-0 = <&pinctrl_usbh1_vbus>;
136 enable-active-high;
139 reg_usbotg_vbus: regulator-usbotg-vbus {
140 compatible = "regulator-fixed";
141 regulator-name = "usbotg_vbus";
142 regulator-min-microvolt = <5000000>;
143 regulator-max-microvolt = <5000000>;
144 pinctrl-names = "default";
145 pinctrl-0 = <&pinctrl_usbotg_vbus>;
147 enable-active-high;
151 compatible = "karo,tx53-audio-sgtl5000", "fsl,imx-audio-sgtl5000";
152 model = "tx53-audio-sgtl5000";
153 ssi-controller = <&ssi1>;
154 audio-codec = <&sgtl5000>;
155 audio-routing =
160 mux-int-port = <1>;
161 mux-ext-port = <5>;
166 pinctrl-names = "default";
167 pinctrl-0 = <&pinctrl_ssi1>;
172 pinctrl-names = "default";
173 pinctrl-0 = <&pinctrl_can1>;
174 xceiver-supply = <®_can_xcvr>;
179 pinctrl-names = "default";
180 pinctrl-0 = <&pinctrl_can2>;
181 xceiver-supply = <®_can_xcvr>;
186 pinctrl-names = "default";
187 pinctrl-0 = <&pinctrl_ecspi1>;
190 cs-gpios = <
198 cd-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
199 fsl,wp-controller;
200 pinctrl-names = "default";
201 pinctrl-0 = <&pinctrl_esdhc1>;
206 cd-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
207 fsl,wp-controller;
208 pinctrl-names = "default";
209 pinctrl-0 = <&pinctrl_esdhc2>;
214 pinctrl-names = "default";
215 pinctrl-0 = <&pinctrl_fec>;
216 phy-mode = "rmii";
217 phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
218 phy-handle = <&phy0>;
219 mac-address = [000000000000]; /* placeholder; will be overwritten by bootloader */
223 #address-cells = <1>;
224 #size-cells = <0>;
226 phy0: ethernet-phy@0 {
228 interrupt-parent = <&gpio2>;
230 device_type = "ethernet-phy";
236 pinctrl-names = "default", "gpio";
237 pinctrl-0 = <&pinctrl_i2c1>;
238 pinctrl-0 = <&pinctrl_i2c1_gpio>;
239 scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
240 sda-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
241 clock-frequency = <400000>;
247 pinctrl-names = "default";
248 pinctrl-0 = <&pinctrl_ds1339>;
249 interrupt-parent = <&gpio4>;
251 trickle-resistor-ohms = <250>;
252 trickle-diode-disable;
257 pinctrl-names = "default";
258 pinctrl-0 = <&pinctrl_hog>;
260 imx53-tx53 {
278 /* MX53_PAD_NANDF_CS2__GPIO6_15 0x1f4 maybe used by EDT-FT5x06 */
279 /* MX53_PAD_EIM_A16__GPIO2_22 0x1f4 maybe used by EDT-FT5x06 */
282 /* MX53_PAD_EIM_A17__GPIO2_21 0x1f4 maybe used by EDT-FT5x06 */
331 pinctrl_can_xcvr: can-xcvrgrp {
389 pinctrl_gpio_key: gpio-keygrp {
400 pinctrl_i2c1_gpio: i2c1-gpiogrp {
414 pinctrl_i2c3_gpio: i2c3-gpiogrp {
503 pinctrl_usbh1_vbus: usbh1-vbusgrp {
509 pinctrl_usbotg_vbus: usbotg-vbusgrp {
523 pinctrl-names = "default";
524 pinctrl-0 = <&pinctrl_nand>;
525 nand-bus-width = <8>;
526 nand-ecc-mode = "hw";
527 nand-on-flash-bbt;
532 pinctrl-names = "default";
533 pinctrl-0 = <&pinctrl_pwm2>;
537 fsl,sdma-ram-script-name = "sdma-imx53.bin";
549 pinctrl-names = "default";
550 pinctrl-0 = <&pinctrl_uart1>;
551 uart-has-rtscts;
556 pinctrl-names = "default";
557 pinctrl-0 = <&pinctrl_uart2>;
558 uart-has-rtscts;
563 pinctrl-names = "default";
564 pinctrl-0 = <&pinctrl_uart3>;
565 uart-has-rtscts;
570 pinctrl-names = "default";
571 pinctrl-0 = <&pinctrl_usbh1>;
573 disable-over-current;
574 vbus-supply = <®_usbh1_vbus>;
581 disable-over-current;
582 vbus-supply = <®_usbotg_vbus>;