dts/microchip/sama5d3xmb.dtsi

1 // SPDX-License-Identifier: GPL-2.0-or-later
3  * sama5d3xmb.dts - Device Tree file for SAMA5D3x mother board
16 				pinctrl-names = "default";
17 				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
21 					bus-width = <4>;
22 					cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
31 					spi-max-frequency = <50000000>;
37 				atmel,clk-from-rk-pin;
50 					clock-names = "mclk";
58 					pinctrl-names = "default";
59 					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
60 					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
61 					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
64 					clock-names = "xvclk";
65 					assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>;
66 					assigned-clock-rates = <25000000>;
70 							remote-endpoint = <&isi_0>;
71 							bus-width = <8>;
79 				pinctrl-names = "default";
80 				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
87 						remote-endpoint = <&ov2640_0>;
88 						bus-width = <8>;
89 						vsync-active = <1>;
90 						hsync-active = <1>;
96 				pinctrl-names = "default";
97 				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
101 					bus-width = <4>;
102 					cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
107 				pinctrl-names = "default";
108 				pinctrl-0 = <
123 …<AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
128 …<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
136 					pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
141 					pinctrl_sensor_reset: sensor_reset-0 {
143 							<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;   /* PE24 gpio */
146 					pinctrl_sensor_power: sensor_power-0 {
148 							<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
153 							<AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
169 			atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
170 			pinctrl-names = "default";
171 			pinctrl-0 = <&pinctrl_usba_vbus>;
176 			num-ports = <3>;
177 			atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH
190 		compatible = "atmel,asoc-wm8904";
191 		pinctrl-names = "default";
192 		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
195 		atmel,audio-routing =
203 		atmel,ssc-controller = <&ssc0>;
204 		atmel,audio-codec = <&wm8904>;