dts/allwinner/sun7i-a20-lamobo-r1.dts

4  * This file is dual-licensed: you can use it either under the terms
43 /dts-v1/;
44 #include "sun7i-a20.dtsi"
45 #include "sunxi-common-regulators.dtsi"
47 #include <dt-bindings/gpio/gpio.h>
48 #include <dt-bindings/interrupt-controller/irq.h>
52 	compatible = "lamobo,lamobo-r1", "allwinner,sun7i-a20";
61 		stdout-path = "serial0:115200n8";
64 	hdmi-connector {
65 		compatible = "hdmi-connector";
70 				remote-endpoint = <&hdmi_out_con>;
76 		compatible = "gpio-leds";
84 	reg_gmac_3v3: gmac-3v3 {
85 		compatible = "regulator-fixed";
86 		regulator-name = "gmac-3v3";
87 		regulator-min-microvolt = <3300000>;
88 		regulator-max-microvolt = <3300000>;
89 		startup-delay-us = <100000>;
90 		enable-active-high;
96 	target-supply = <&reg_ahci_5v>;
105 	cpu-supply = <&reg_dcdc2>;
121 	pinctrl-names = "default";
122 	pinctrl-0 = <&gmac_rgmii_pins>;
123 	phy-mode = "rgmii";
124 	phy-supply = <&reg_gmac_3v3>;
127 	fixed-link {
129 		full-duplex;
133 		compatible = "snps,dwmac-mdio";
134 		#address-cells = <1>;
135 		#size-cells = <0>;
137 		switch: ethernet-switch@1e {
142 				#address-cells = <1>;
143 				#size-cells = <0>;
174 					phy-mode = "rgmii-txid";
175 					fixed-link {
177 						full-duplex;
191 		remote-endpoint = <&hdmi_con_in>;
200 		interrupt-parent = <&nmi_intc>;
210 	pinctrl-names = "default";
211 	pinctrl-0 = <&ir0_rx_pin>;
216 	vmmc-supply = <&reg_vcc3v3>;
217 	bus-width = <4>;
218 	cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
246 	regulator-always-on;
247 	regulator-min-microvolt = <1000000>;
248 	regulator-max-microvolt = <1400000>;
249 	regulator-name = "vdd-cpu";
253 	regulator-always-on;
254 	regulator-min-microvolt = <1000000>;
255 	regulator-max-microvolt = <1400000>;
256 	regulator-name = "vdd-int-dll";
260 	regulator-name = "vdd-rtc";
264 	regulator-always-on;
265 	regulator-min-microvolt = <3000000>;
266 	regulator-max-microvolt = <3000000>;
267 	regulator-name = "avcc";
280 	pinctrl-names = "default";
281 	pinctrl-0 = <&spi0_pi_pins>,
288 	pinctrl-names = "default";
289 	pinctrl-0 = <&uart0_pb_pins>;
294 	pinctrl-names = "default";
295 	pinctrl-0 = <&uart3_ph_pins>;
300 	pinctrl-names = "default";
301 	pinctrl-0 = <&uart7_pi_pins>;
315 	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
316 	usb0_vbus_power-supply = <&usb_power_supply>;
317 	usb0_vbus-supply = <&reg_usb0_vbus>;
318 	usb2_vbus-supply = <&reg_usb2_vbus>;