Lines Matching +full:super +full:- +full:speed
10 Addresses scanned: ISA address retrieved from Super I/O registers
18 Addresses scanned: ISA address retrieved from Super I/O registers
22 * Winbond W83627DHG-P
26 Addresses scanned: ISA address retrieved from Super I/O registers
34 Addresses scanned: ISA address retrieved from Super I/O registers
42 Addresses scanned: ISA address retrieved from Super I/O registers
46 * Winbond W83667HG-B
50 Addresses scanned: ISA address retrieved from Super I/O registers
54 * Nuvoton NCT6775F/W83667HG-I
58 Addresses scanned: ISA address retrieved from Super I/O registers
66 Addresses scanned: ISA address retrieved from Super I/O registers
73 - Jean Delvare <jdelvare@suse.de>
74 - Yuan Mu (Winbond)
75 - Rudolf Marek <r.marek@assembler.cz>
76 - David Hubbard <david.c.hubbard@gmail.com>
77 - Gong Jun <JGong@nuvoton.com>
80 -----------
83 W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I
84 (NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively
88 2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID
92 The temperature sensor sources on W82677HG-B, NCT6775F, and NCT6776F are
100 resolution is 1 degC for W83667HG-B and 0.0 degC for NCT6775F and NCT6776F.
106 triggered if the rotation speed has dropped below a programmable limit. Fan
121 The mode works for fan1-fan4. Mapping of temperatures to pwm outputs is as
124 temp1 -> pwm1
125 temp2 -> pwm2
126 temp3 -> pwm3 (not on 627UHG)
127 prog -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not
131 ----------
138 pwm[1-4]
139 this file stores PWM duty cycle or DC value (fan speed) in range:
143 pwm[1-4]_enable
146 * 1 Manual mode, write to pwm file any value 0-255 (full speed)
148 * 3 "Fan Speed Cruise" mode
155 startup, and is only supported for W83677HG-B, NCT6775F, and NCT6776F.
163 pwm[1-4]_mode
166 * 0 DC output (0 - 12v)
170 -------------------
174 pwm[1-4]_target
176 (range 0 - 127000)
177 pwm[1-4]_tolerance
178 tolerance, unit millidegree Celsius (range 0 - 15000)
180 there are no changes to fan speed. Once the temperature leaves the interval,
181 fan speed increases (temp is higher) or decreases if lower than desired.
184 pwm[1-4]_min_output
185 minimum fan speed (range 1 - 255), when the temperature
187 pwm[1-4]_stop_time
191 pwm[1-4]_start_output
192 minimum fan speed (range 1 - 255) when spinning up
193 pwm[1-4]_step_output
194 rate of fan speed change (1 - 255)
195 pwm[1-4]_stop_output
196 minimum fan speed (range 1 - 255) when spinning down
197 pwm[1-4]_max_output
198 maximum fan speed (range 1 - 255), when the temperature
205 ----------------------
209 different power-on default values, but BIOS should already be loading
237 0x50-0x55 and 0x650-0x657 marked as:
239 - "Test Register" for the EHF
240 - "Reserved Register" for the DHG
245 southbridge drives the fans. And the DHG supports SST, a one-wire serial bus.
247 The DHG-P has an additional automatic fan speed control mode named Smart Fan