Lines Matching +full:data +full:- +full:sheet
8 Note that these settings are applied after any phy-specific fixup from
17 skew values actually increase in 120ps steps, starting from -840ps. The
28 -----------------------------------------------------
29 0 -840ps 0000
30 200 -720ps 0001
31 400 -600ps 0010
32 600 -480ps 0011
33 800 -360ps 0100
34 1000 -240ps 0101
35 1200 -120ps 0110
48 - rxc-skew-ps : Skew control of RXC pad
49 - rxdv-skew-ps : Skew control of RX CTL pad
50 - txc-skew-ps : Skew control of TXC pad
51 - txen-skew-ps : Skew control of TX CTL pad
52 - rxd0-skew-ps : Skew control of RX data 0 pad
53 - rxd1-skew-ps : Skew control of RX data 1 pad
54 - rxd2-skew-ps : Skew control of RX data 2 pad
55 - rxd3-skew-ps : Skew control of RX data 3 pad
56 - txd0-skew-ps : Skew control of TX data 0 pad
57 - txd1-skew-ps : Skew control of TX data 1 pad
58 - txd2-skew-ps : Skew control of TX data 2 pad
59 - txd3-skew-ps : Skew control of TX data 3 pad
64 value is 0, and the maximum is property-dependent. The increment
66 rxc-skew-ps=<0> actually results in -900 picoseconds adjustment.
74 The following 5-bit values table apply to rxc-skew-ps and txc-skew-ps.
77 ------------------------------------------------------
78 0_0000 -900ps 0
79 0_0001 -840ps 60
80 0_0010 -780ps 120
81 0_0011 -720ps 180
82 0_0100 -660ps 240
83 0_0101 -600ps 300
84 0_0110 -540ps 360
85 0_0111 -480ps 420
86 0_1000 -420ps 480
87 0_1001 -360ps 540
88 0_1010 -300ps 600
89 0_1011 -240ps 660
90 0_1100 -180ps 720
91 0_1101 -120ps 780
92 0_1110 -60ps 840
111 The following 4-bit values table apply to the txdX-skew-ps, rxdX-skew-ps
112 data pads, and the rxdv-skew-ps, txen-skew-ps control pads.
115 ------------------------------------------------------
116 0000 -420ps 0
117 0001 -360ps 60
118 0010 -300ps 120
119 0011 -240ps 180
120 0100 -180ps 240
121 0101 -120ps 300
122 0110 -60ps 360
137 - rxc-skew-ps : Skew control of RX clock pad
138 - txc-skew-ps : Skew control of TX clock pad
142 - rxdv-skew-ps : Skew control of RX CTL pad
143 - txen-skew-ps : Skew control of TX CTL pad
144 - rxd0-skew-ps : Skew control of RX data 0 pad
145 - rxd1-skew-ps : Skew control of RX data 1 pad
146 - rxd2-skew-ps : Skew control of RX data 2 pad
147 - rxd3-skew-ps : Skew control of RX data 3 pad
148 - txd0-skew-ps : Skew control of TX data 0 pad
149 - txd1-skew-ps : Skew control of TX data 1 pad
150 - txd2-skew-ps : Skew control of TX data 2 pad
151 - txd3-skew-ps : Skew control of TX data 3 pad
153 - micrel,force-master:
165 A negative value can be assigned as rxc-skew-psec = <(-100)>;.
169 Range of the value -700 to 2400, default value 0:
171 - rxc-skew-psec : Skew control of RX clock pad
172 - txc-skew-psec : Skew control of TX clock pad
174 Range of the value -700 to 800, default value 0:
176 - rxdv-skew-psec : Skew control of RX CTL pad
177 - txen-skew-psec : Skew control of TX CTL pad
178 - rxd0-skew-psec : Skew control of RX data 0 pad
179 - rxd1-skew-psec : Skew control of RX data 1 pad
180 - rxd2-skew-psec : Skew control of RX data 2 pad
181 - rxd3-skew-psec : Skew control of RX data 3 pad
182 - txd0-skew-psec : Skew control of TX data 0 pad
183 - txd1-skew-psec : Skew control of TX data 1 pad
184 - txd2-skew-psec : Skew control of TX data 2 pad
185 - txd3-skew-psec : Skew control of TX data 3 pad
191 rxc-skew-ps = <1800>;
192 rxdv-skew-ps = <0>;
193 txc-skew-ps = <1800>;
194 txen-skew-ps = <0>;
198 /* Attach to an explicitly-specified PHY */
200 phy0: ethernet-phy@0 {
201 rxc-skew-ps = <1800>;
202 rxdv-skew-ps = <0>;
203 txc-skew-ps = <1800>;
204 txen-skew-ps = <0>;
210 phy-mode = "rgmii-id";
215 Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014.
216 http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf
218 Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014.
223 Note that a previous version of the Micrel ksz9021rl/rn Data Sheet
224 was missing extended register 106 (transmit data pad skews), and