Lines Matching +full:ethernet +full:- +full:port
1 # SPDX-License-Identifier: (GPL-2.0 OR MIT)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Vladimir Oltean <vladimir.oltean@nxp.com>
11 - Claudiu Manoil <claudiu.manoil@nxp.com>
12 - Alexandre Belloni <alexandre.belloni@bootlin.com>
13 - UNGLinuxDriver@microchip.com
16 There are multiple switches which are either part of the Ocelot-1 family, or
20 them performs packet I/O primarily through an Ethernet port of the switch
21 (which is attached to an Ethernet port of the host), rather than through
22 Frame DMA or register-based I/O.
26 This is found in the NXP T1040, where it is a memory-mapped platform
31 - phy-mode = "internal": on ports 8 and 9
32 - phy-mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7
33 - phy-mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7
34 - phy-mode = "1000base-x": on ports 0, 1, 2, 3, 4, 5, 6, 7
39 enetc root complex. As a result, the ethernet-switch node is a sub-node of
43 If any external switch port is enabled, the enetc PF2 (enetc_port2) should
46 port 2 and not to Felix.
50 - phy-mode = "internal": on ports 4 and 5
51 - phy-mode = "sgmii": on ports 0, 1, 2, 3
52 - phy-mode = "qsgmii": on ports 0, 1, 2, 3
53 - phy-mode = "usxgmii": on ports 0, 1, 2, 3
54 - phy-mode = "1000base-x": on ports 0, 1, 2, 3
55 - phy-mode = "2500base-x": on ports 0, 1, 2, 3
60 - mscc,vsc9953-switch
61 - pci1957,eef0
73 little-endian: true
74 big-endian: true
77 - compatible
78 - reg
81 - $ref: dsa.yaml#/$defs/ethernet-ports
82 - if:
88 - interrupts
94 - |
95 #include <dt-bindings/interrupt-controller/arm-gic.h>
98 #address-cells = <3>;
99 #size-cells = <2>;
101 ethernet-switch@0,5 {
106 ethernet-ports {
107 #address-cells = <1>;
108 #size-cells = <0>;
110 port@0 {
112 phy-mode = "qsgmii";
113 phy-handle = <&phy0>;
114 managed = "in-band-status";
117 port@1 {
119 phy-mode = "qsgmii";
120 phy-handle = <&phy1>;
121 managed = "in-band-status";
124 port@2 {
126 phy-mode = "qsgmii";
127 phy-handle = <&phy2>;
128 managed = "in-band-status";
131 port@3 {
133 phy-mode = "qsgmii";
134 phy-handle = <&phy3>;
135 managed = "in-band-status";
138 port@4 {
140 ethernet = <&enetc_port2>;
141 phy-mode = "internal";
143 fixed-link {
145 full-duplex;
150 port@5 {
152 ethernet = <&enetc_port3>;
153 phy-mode = "internal";
155 fixed-link {
157 full-duplex;
165 - |
167 #address-cells = <1>;
168 #size-cells = <1>;
170 ethernet-switch@800000 {
171 compatible = "mscc,vsc9953-switch";
173 little-endian;
175 ethernet-ports {
176 #address-cells = <1>;
177 #size-cells = <0>;
179 port@0 {
181 phy-mode = "qsgmii";
182 phy-handle = <&phy0>;
183 managed = "in-band-status";
186 port@1 {
188 phy-mode = "qsgmii";
189 phy-handle = <&phy1>;
190 managed = "in-band-status";
193 port@2 {
195 phy-mode = "qsgmii";
196 phy-handle = <&phy2>;
197 managed = "in-band-status";
200 port@3 {
202 phy-mode = "qsgmii";
203 phy-handle = <&phy3>;
204 managed = "in-band-status";
207 port@4 {
209 phy-mode = "qsgmii";
210 phy-handle = <&phy4>;
211 managed = "in-band-status";
214 port@5 {
216 phy-mode = "qsgmii";
217 phy-handle = <&phy5>;
218 managed = "in-band-status";
221 port@6 {
223 phy-mode = "qsgmii";
224 phy-handle = <&phy6>;
225 managed = "in-band-status";
228 port@7 {
230 phy-mode = "qsgmii";
231 phy-handle = <&phy7>;
232 managed = "in-band-status";
235 port@8 {
237 phy-mode = "internal";
238 ethernet = <&enet0>;
240 fixed-link {
242 full-duplex;
247 port@9 {
249 phy-mode = "internal";
250 ethernet = <&enet1>;
252 fixed-link {
254 full-duplex;