Lines Matching +full:ethernet +full:- +full:switch
1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Marvell MV88E6xxx DSA switch family
10 - Andrew Lunn <andrew@lunn.ch>
13 The Marvell MV88E6xxx switch series has been produced and sold
14 by Marvell since at least 2008. The switch has a few compatibles which
15 just indicate the base address of the switch, then operating systems
16 can investigate switch ID registers to find out which actual version
17 of the switch it is dealing with.
22 - enum:
23 - marvell,mv88e6085
24 - marvell,mv88e6190
25 - marvell,mv88e6250
27 marvell,mv88e6085: This switch uses base address 0x10.
28 This switch and its siblings will be autodetected from
29 ID registers found in the switch, so only "marvell,mv88e6085" should be
33 marvell,mv88e6190: This switch uses base address 0x00.
34 This switch and its siblings will be autodetected from
35 ID registers found in the switch, so only "marvell,mv88e6190" should be
38 marvell,mv88e6250: This switch uses base address 0x08 or 0x18.
39 This switch and its siblings will be autodetected from
40 ID registers found in the switch, so only "marvell,mv88e6250" should be
43 - items:
44 - const: marvell,turris-mox-mv88e6085
45 - const: marvell,mv88e6085
46 - items:
47 - const: marvell,turris-mox-mv88e6190
48 - const: marvell,mv88e6190
53 eeprom-length:
55 description: Set to the length of an EEPROM connected to the switch. Must be
56 set if the switch can not detect the presence and/or size of a connected
59 reset-gpios:
65 description: The switch provides an external interrupt line, but it is
69 interrupt-controller:
70 description: The switch has an internal interrupt controller used by
71 the different sub-blocks.
73 '#interrupt-cells':
87 mdio-external:
95 const: marvell,mv88e6xxx-mdio-external
98 - compatible
101 - $ref: dsa.yaml#/$defs/ethernet-ports
104 - compatible
105 - reg
110 - |
111 #include <dt-bindings/gpio/gpio.h>
113 #address-cells = <1>;
114 #size-cells = <0>;
116 ethernet-switch@0 {
119 reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
122 #address-cells = <1>;
123 #size-cells = <0>;
125 sw_phy0: ethernet-phy@0 {
129 sw_phy1: ethernet-phy@1 {
133 sw_phy2: ethernet-phy@2 {
137 sw_phy3: ethernet-phy@3 {
142 ethernet-ports {
143 #address-cells = <1>;
144 #size-cells = <0>;
146 ethernet-port@0 {
149 phy-handle = <&sw_phy0>;
150 phy-mode = "internal";
153 ethernet-port@1 {
156 phy-handle = <&sw_phy1>;
157 phy-mode = "internal";
160 ethernet-port@2 {
163 phy-handle = <&sw_phy2>;
164 phy-mode = "internal";
167 ethernet-port@3 {
170 phy-handle = <&sw_phy3>;
171 phy-mode = "internal";
174 ethernet-port@5 {
176 ethernet = <&fec>;
177 phy-mode = "rgmii-id";
179 fixed-link {
181 full-duplex;
187 - |
188 #include <dt-bindings/interrupt-controller/irq.h>
190 #address-cells = <1>;
191 #size-cells = <0>;
193 ethernet-switch@0 {
195 #interrupt-cells = <2>;
196 interrupt-controller;
197 interrupt-parent = <&gpio1>;
199 pinctrl-0 = <&switch_interrupt_pins>;
200 pinctrl-names = "default";
204 #address-cells = <1>;
205 #size-cells = <0>;
207 switch0phy1: ethernet-phy@1 {
211 switch0phy2: ethernet-phy@2 {
215 switch0phy3: ethernet-phy@3 {
219 switch0phy4: ethernet-phy@4 {
223 switch0phy5: ethernet-phy@5 {
227 switch0phy6: ethernet-phy@6 {
231 switch0phy7: ethernet-phy@7 {
235 switch0phy8: ethernet-phy@8 {
240 mdio-external {
241 compatible = "marvell,mv88e6xxx-mdio-external";
242 #address-cells = <1>;
243 #size-cells = <0>;
245 phy1: ethernet-phy@b {
247 compatible = "ethernet-phy-ieee802.3-c45";
250 phy2: ethernet-phy@c {
252 compatible = "ethernet-phy-ieee802.3-c45";
256 ethernet-ports {
257 #address-cells = <1>;
258 #size-cells = <0>;
260 ethernet-port@0 {
261 ethernet = <ð0>;
262 phy-mode = "rgmii";
265 fixed-link {
266 full-duplex;
272 ethernet-port@1 {
274 phy-handle = <&switch0phy1>;
278 ethernet-port@2 {
280 phy-handle = <&switch0phy2>;
284 ethernet-port@3 {
286 phy-handle = <&switch0phy3>;
290 ethernet-port@4 {
292 phy-handle = <&switch0phy4>;
296 ethernet-port@5 {
298 phy-handle = <&switch0phy5>;
302 ethernet-port@6 {
304 phy-handle = <&switch0phy6>;
308 ethernet-port@7 {
310 phy-handle = <&switch0phy7>;
314 ethernet-port@8 {
316 phy-handle = <&switch0phy8>;
320 ethernet-port@9 {
323 phy-handle = <&phy1>;
324 phy-mode = "xaui";
328 ethernet-port@a {
331 phy-handle = <&phy2>;
332 phy-mode = "xaui";