Lines Matching full:specifies

32       Specifies the GPIO connected to the device's active-low RDY output.
37       Specifies the GPIO connected to the device's active-low MCLR input. The
45       Specifies the maximum number of conversion periods (counts) that can be
56       Specifies the number of conversions to occur before an interrupt is
67     description: Specifies the preloaded ATI fine fractional divider.
73     description: Specifies the preloaded ATI coarse fractional divider.
79     description: Specifies the preloaded ATI compensation selection.
86       Specifies the long-term average filter damping factor to be applied during
94       Specifies the long-term average filter damping factor to be applied during
102       Specifies the counts filter damping factor to be applied during low-power
110       Specifies the counts filter damping factor to be applied during normal-
118       Specifies the long-term average filter fast damping factor to be applied
126       Specifies the long-term average filter fast damping factor to be applied
134       Specifies the delay (in ms) before ATI is retried following an ATI error.
139     description: Specifies the rate (in ms) at which ATI status is evaluated.
145       Specifies the length of time (in ms) to wait for an event before moving
151     description: Specifies the report rate (in ms) during normal-power mode.
157       Specifies the length of time (in ms) to wait for an event before moving
163     description: Specifies the report rate (in ms) during low-power mode.
169       Specifies the rate (in ms) at which channels not regularly sampled during
175     description: Specifies the report rate (in ms) during ultra-low-power mode.
196           Specifies the order of the channels that participate in the trackpad.
204         description: Specifies the number of rows that comprise the trackpad.
210         description: Specifies the number of columns that comprise the trackpad.
218           Specifies the speed (in coordinates traveled per conversion) after
226           Specifies the speed (in coordinates traveled per conversion) after
242         description: Specifies the trackpad's lower starting points.
248         description: Specifies the trackpad's upper starting points.
272               Specifies the length of time (in ms) within which a tap, swipe
282               Specifies the length of time (in ms) for which a tap gesture must
290               Specifies the distance (in coordinates) across which a swipe or
295               For tap gestures, this property specifies the distance from the
307               Specifies one or more GPIO mapped to the event as follows:
333         description: Specifies the cycle's conversion period.
339         description: Specifies the cycle's conversion frequency fraction.
348         description: Specifies the CTx pin(s) associated with the cycle.
372           Specifies the cycle's sensing mode as follows:
390         description: Specifies the cycle's current reference level.
396         description: Specifies the cycle's current reference trim.
424         description: Specifies a separate reference channel to be followed.
430         description: Specifies the relative weight of the reference channel.
446           Specifies the channel's ATI band as a fraction of its ATI target as
456           Specifies that the channel's long-term average is to freeze if any
468           Specifies that the channel's long-term average is to freeze in the
479         description: Specifies the CRx pin(s) associated with the channel.
493           Specifies the bias current applied during mutual (projected)
505         description: Specifies the channel's ATI target.
512         description: Specifies the channel's ATI base.
518           Specifies the channel's ATI mode as follows:
530         description: Specifies the channel's ATI fine fractional divider.
536         description: Specifies the channel's ATI coarse fractional multiplier.
542         description: Specifies the channel's ATI coarse fractional divider.
548         description: Specifies the channel's ATI compensation divider.
554         description: Specifies the channel's ATI compensation selection.
560         description: Specifies the channel's debounce entrance factor.
566         description: Specifies the channel's debounce exit factor.
584               Specifies one or more GPIO mapped to the event as follows:
596               Specifies the threshold for the event. Valid entries range from
604               Specifies the hysteresis for the event (touch events only).
611               Specifies the length of time (in ms) to wait before automatically
624               Specifies whether the event is to be interpreted as a key (1)
648           Specifies the order of the channels that participate in the slider.
655           Specifies the slider's one-dimensional resolution, equal to the
662         description: Specifies the slider's lower starting point.
668         description: Specifies the slider's upper starting point.
675           Specifies the speed (in coordinates traveled per conversion) after
683           Specifies the speed (in coordinates traveled per conversion) after
691           Specifies the coordinate filter damping factor to be applied
711           Specifies the absolute axis to which coordinates are mapped. Specify
730               Specifies the length of time (in ms) within which a tap, swipe
740               Specifies the length of time (in ms) for which a tap gesture must
749               Specifies the distance (in coordinates) across which a swipe or
762               Specifies one or more GPIO mapped to the event as follows: