Lines Matching +full:dual +full:- +full:mode
1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/connector/usb-connector.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Rob Herring <robh@kernel.org>
20 - enum:
21 - usb-a-connector
22 - usb-b-connector
23 - usb-c-connector
25 - items:
26 - const: gpio-usb-b-connector
27 - const: usb-b-connector
29 - items:
30 - const: samsung,usb-connector-11pin
31 - const: usb-b-connector
41 non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible
46 - mini
47 - micro
49 self-powered:
53 # The following are optional properties for "usb-b-connector".
54 id-gpios:
58 vbus-gpios:
63 vbus-supply:
65 mode or dual role mode is supported.
67 model it as a regulator. See bindings/regulator/fixed-regulator.yaml
69 power-role:
71 support. "dual" refers to Dual Role Port (DRP).
75 - source
76 - sink
77 - dual
79 try-power-role:
84 - source
85 - sink
86 - dual
88 data-role:
89 description: Data role if Type C connector supports USB data. "dual" refers
90 Dual Role Device (DRD).
94 - host
95 - device
96 - dual
98 typec-power-opmode:
99 description: Determines the power operation mode that the Type C connector
102 - "default" corresponds to default USB voltage and current defined by the
104 5V 900mA or 1500mA for USB 3.2 ports in single-lane or dual-lane
106 - "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB
107 Type-C Cable and Connector specification, when Power Delivery is not
111 - default
112 - 1.5A
113 - 3.0A
115 pd-disable:
116 description: Set this property if the Type-C connector has no power delivery support.
119 # The following are optional properties for "usb-c-connector" with power
121 sink-vdos:
125 "USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10"
128 dt-bindings/usb/pd.h.
131 $ref: /schemas/types.yaml#/definitions/uint32-array
133 sink-vdos-v1:
139 dt-bindings/usb/pd.h.
142 $ref: /schemas/types.yaml#/definitions/uint32-array
144 accessory-mode-audio:
146 description: Whether the device supports Audio Adapter Accessory Mode. This
150 accessory-mode-debug:
152 description: Whether the device supports Debug Accessory Mode. This
169 A single USB-C Alternative Mode as supported by the USB-C connector logic.
176 description: Unique value assigned by USB-IF to the Vendor / AltMode.
207 description: Sideband Use (SBU), present in USB-C. This describes the
208 alternate mode connection of which SBU is a part.
211 - port@0
213 new-source-frs-typec-current:
215 is applied during PD3.0 Fast Role Swap. "Table 6-14 Fixed Supply PDO - Sink"
217 different power levels and "6.4.1.3.1.6 Fast Role Swap USB Type-C Current"
226 "1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink".
232 slow-charger-loop:
236 Revision 3.0, Version 1.2. When the property is set, the port requests pSnkStby(2.5W -
239 SNK_READY for non-pd link.
247 "^caps-[0-9]+$":
257 sink-vdos-v1: [ sink-vdos ]
258 sink-vdos: [ sink-vdos-v1 ]
261 - compatible
268 source-pdos:
273 the PD spec chapter 6.4.1. Required for power source and power dual role.
275 defined in dt-bindings/usb/pd.h.
278 $ref: /schemas/types.yaml#/definitions/uint32-array
280 sink-pdos:
285 PD spec chapter 6.4.1. Required for power sink and power dual role. User
287 in dt-bindings/usb/pd.h.
290 $ref: /schemas/types.yaml#/definitions/uint32-array
292 op-sink-microwatt:
295 power dual role.
298 - $ref: "#/$defs/capabilities"
299 - if:
303 const: gpio-usb-b-connector
306 - required:
307 - vbus-gpios
308 - required:
309 - id-gpios
311 - if:
315 const: samsung,usb-connector-11pin
322 - not:
324 - typec-power-opmode
325 - new-source-frs-typec-current
330 # Micro-USB connector with HS lines routed via controller (MUIC).
331 - |
332 muic-max77843 {
334 compatible = "usb-b-connector";
335 label = "micro-USB";
340 # USB-C connector attached to CC controller (s2mm005), HS lines routed
343 - |
346 compatible = "usb-c-connector";
347 label = "USB-C";
357 #address-cells = <1>;
358 #size-cells = <0>;
363 remote-endpoint = <&max77865_usbc_hs>;
369 remote-endpoint = <&usbdrd_phy_ss>;
375 remote-endpoint = <&dp_aux>;
382 # USB-C connector attached to a typec port controller(ptn5110), which has
384 - |
385 #include <dt-bindings/usb/pd.h>
388 compatible = "usb-c-connector";
389 label = "USB-C";
390 power-role = "dual";
391 try-power-role = "sink";
392 source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
393 sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)
395 op-sink-microwatt = <10000000>;
399 # USB-C connector attached to SoC with a single High-Speed controller
400 - |
402 compatible = "usb-c-connector";
403 label = "USB-C";
407 remote-endpoint = <&usb_hs_ep>;
412 # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220)
415 - |
417 compatible = "usb-c-connector";
418 label = "USB-C";
419 data-role = "dual";
422 #address-cells = <1>;
423 #size-cells = <0>;
427 remote-endpoint = <&usb3_hs_ep>;
433 remote-endpoint = <&hd3ss3220_in_ep>;
440 - |
441 #include <dt-bindings/gpio/gpio.h>
445 compatible = "gpio-usb-b-connector", "usb-b-connector";
447 id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
448 vbus-supply = <&usb_p0_vbus>;
452 # Micro-USB connector with HS lines routed via controller (MUIC) and MHL
453 # lines connected to HDMI-MHL bridge (sii8620) on Samsung Exynos5433-based
455 - |
456 muic-max77843 {
458 compatible = "samsung,usb-connector-11pin", "usb-b-connector";
459 label = "micro-USB";
463 #address-cells = <1>;
464 #size-cells = <0>;
469 remote-endpoint = <&usb_to_muic>;
475 remote-endpoint = <&sii8620_mhl>;