Lines Matching +full:power +full:- +full:monitor

3 Contact:	linux-scsi@vger.kernel.org
5 		This file contains the auto-hibernate idle timer setting of a
6 		UFS host controller. A value of '0' means auto-hibernate is not
9 		the link into hibernate state. That will save power at the
11 		10-bit values with a power-of-ten multiplier which allows a
104 Description:	This file shows value that defines the power mode after
273 		written during the pre-soldering phase of the PSA flow.
307 Description:	This file shows the MIPI M-PHY version number in BCD format.
395 Description:	This file shows the maximum data-in buffer size. This
406 Description:	This file shows the maximum data-out buffer size. This
439 Description:	This file shows support for out-of-order data transfer.
507 		enhanced type 1-4). This is one of the UFS geometry
519 		enhanced type 1-4). This is one of the UFS geometry
566 		power descriptor parameters. The full information about
669 Description:	This file defines the device behavior when a power failure
766 		logical units configured as power on write protected. The
837 Description:	This file provides the current power mode UFS device attribute.
927 		read-write persistent attribute and is equal to two after device
978 		load to all logical units in pre-soldering state.
1001 		runtime power management level. The current driver
1027 Description:	This entry shows the target power mode of an UFS device
1028 		for the chosen runtime power management level.
1037 		for the chosen runtime power management level.
1046 		system power management level. The current driver
1072 Description:	This entry shows the target power mode of an UFS device
1073 		for the chosen system power management level.
1082 		for the chosen system power management level.
1086 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/monitor_enable
1087 What:		/sys/bus/platform/devices/*.ufs/monitor/monitor_enable
1090 Description:	This file shows the status of performance monitor enablement
1091 		and it can be used to start/stop the monitor. When the monitor
1094 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/monitor_chunk_size
1095 What:		/sys/bus/platform/devices/*.ufs/monitor/monitor_chunk_size
1098 Description:	This file tells the monitor to focus on requests transferring
1100 		It can only be changed when monitor is disabled.
1102 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/read_total_sectors
1103 What:		/sys/bus/platform/devices/*.ufs/monitor/read_total_sectors
1107 		sent from device to host after monitor gets started.
1111 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/read_total_busy
1112 What:		/sys/bus/platform/devices/*.ufs/monitor/read_total_busy
1116 		sending data from device to host after monitor gets started.
1120 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/read_nr_requests
1121 What:		/sys/bus/platform/devices/*.ufs/monitor/read_nr_requests
1125 		monitor gets started.
1129 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_max
1130 What:		/sys/bus/platform/devices/*.ufs/monitor/read_req_latency_max
1134 		read requests after monitor gets started.
1138 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_min
1139 What:		/sys/bus/platform/devices/*.ufs/monitor/read_req_latency_min
1143 		read requests after monitor gets started.
1147 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_avg
1148 What:		/sys/bus/platform/devices/*.ufs/monitor/read_req_latency_avg
1152 		read requests after monitor gets started.
1156 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_sum
1157 What:		/sys/bus/platform/devices/*.ufs/monitor/read_req_latency_sum
1161 		read requests sent after monitor gets started.
1165 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/write_total_sectors
1166 What:		/sys/bus/platform/devices/*.ufs/monitor/write_total_sectors
1170 		from host to device after monitor gets started.
1174 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/write_total_busy
1175 What:		/sys/bus/platform/devices/*.ufs/monitor/write_total_busy
1179 		sending data from host to device after monitor gets started.
1183 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/write_nr_requests
1184 What:		/sys/bus/platform/devices/*.ufs/monitor/write_nr_requests
1188 		monitor gets started.
1192 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_max
1193 What:		/sys/bus/platform/devices/*.ufs/monitor/write_req_latency_max
1197 		requests after monitor gets started.
1201 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_min
1202 What:		/sys/bus/platform/devices/*.ufs/monitor/write_req_latency_min
1206 		requests after monitor gets started.
1210 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_avg
1211 What:		/sys/bus/platform/devices/*.ufs/monitor/write_req_latency_avg
1215 		requests after monitor gets started.
1219 What:		/sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_sum
1220 What:		/sys/bus/platform/devices/*.ufs/monitor/write_req_latency_sum
1224 		requests after monitor gets started.
1241 Description:	This file shows the PA power mode of UFS.
1265 Description:	This file shows the UFS device power mode.
1281 Description:	This entry shows if preserve user-space was configured
1306 Description:	This entry shows the total user-space decrease in shared
1444 		01h  0% - 10% WriteBooster Buffer life time used
1446 		0Ah  90% - 100% WriteBooster Buffer life time used
1465 		enable it. The WriteBooster is enabled after power-on/reset,
1474 Contact:	Jinyoung Choi <j-young.choi@samsung.com>
1496 		host-device pair. i.e. the capabilities which are enabled in the
1541 		Symbol - VER.  This file shows the UFSHCD version.
1550 		Symbol - HCPID.  This file shows the UFSHCD product id.
1559 		Symbol - HCMID. This file shows the UFSHCD manufacturer id.
1560 		The Manufacturer ID is defined by JEDEC in JEDEC-JEP106.