Lines Matching +full:level +full:- +full:low
3 Contact: linux-iio@vger.kernel.org
11 Contact: linux-iio@vger.kernel.org
16 MTCLKA-MTCLKB:
20 MTCLKC-MTCLKD:
26 Contact: linux-iio@vger.kernel.org
33 Contact: linux-iio@vger.kernel.org
39 Contact: linux-iio@vger.kernel.org
45 Contact: linux-iio@vger.kernel.org
52 Contact: linux-iio@vger.kernel.org
59 Contact: linux-iio@vger.kernel.org
78 non-recycle:
80 underflow takes place. The counter is re-enabled when a
84 modulo-n:
94 The output signal is initially low, and will remain low
99 hardware retriggerable one-shot:
101 will go low by a trigger input signal, and will remain
102 low until the counter reaches zero. The output will then
105 value and setting the output signal low, thus starting
106 the one-shot pulse.
110 has decremented to 1, the output signal goes low for one
127 the count expires, the output signal goes low and the
136 expires, the output will go low for one clock pulse and
143 output signal will go low for one clock pulse and then
153 Contact: linux-iio@vger.kernel.org
161 Contact: linux-iio@vger.kernel.org
163 Read-only attribute that indicates the count direction of Count
174 Contact: linux-iio@vger.kernel.org
188 Contact: linux-iio@vger.kernel.org
190 Read-only attribute that indicates whether excessive noise is
195 Contact: linux-iio@vger.kernel.org
207 pulse-direction:
209 The input level of signal B determines direction.
242 Contact: linux-iio@vger.kernel.org
244 Read-only attribute that indicates the device-specific name of
250 Contact: linux-iio@vger.kernel.org
259 Contact: linux-iio@vger.kernel.org
261 If the counter device supports preset registers -- registers
262 used to load counter channels to a set count upon device-defined
263 preset operation trigger events -- the preset count for channel
268 Contact: linux-iio@vger.kernel.org
275 Contact: linux-iio@vger.kernel.org
284 Pulse-Direction count function mode, this Signal is
288 Low state transitions to high state.
291 High state transitions to low state.
298 Contact: linux-iio@vger.kernel.org
324 Contact: linux-iio@vger.kernel.org
326 Read-only attribute that indicates the component ID of the
331 Contact: linux-iio@vger.kernel.org
340 Contact: linux-iio@vger.kernel.org
344 rounded-up to a power of 2.
348 Contact: linux-iio@vger.kernel.org
350 Read-only attribute that indicates the device-specific name of
356 Contact: linux-iio@vger.kernel.org
358 Read-only attribute that indicates the total number of Counts
363 Contact: linux-iio@vger.kernel.org
365 Read-only attribute that indicates the total number of Signals
370 Contact: linux-iio@vger.kernel.org
372 Read-only attribute that indicates whether a differential
380 Contact: linux-iio@vger.kernel.org
388 Contact: linux-iio@vger.kernel.org
395 Contact: linux-iio@vger.kernel.org
397 Active level of index input Signal Y; irrelevant in
398 non-synchronous load mode.
403 Contact: linux-iio@vger.kernel.org
410 Contact: linux-iio@vger.kernel.org
412 Active level of Signal Y. The following polarity values are
416 Signal high state considered active level (rising edge).
419 Signal low state considered active level (falling edge).
423 Contact: linux-iio@vger.kernel.org
425 Read-only attribute that indicates the device-specific name of
431 Contact: linux-iio@vger.kernel.org
433 Signal level state of Signal Y. The following signal level
436 low:
437 Low level state.
440 High level state.
444 Contact: linux-iio@vger.kernel.org
447 non-synchronous or synchronous load mode. Synchronous load mode
448 cannot be selected in non-quadrature (Pulse-Direction) clock
451 non-synchronous:
452 A logic low level is the active level at this index
454 is performed directly on the active level of the index
459 quadrature clock mode. The active level is configured
462 quadrature clock on the active level of the index input.
466 Contact: linux-iio@vger.kernel.org
468 Read-only attribute that indicates the signal Y frequency, in Hz.