Lines Matching +full:clock +full:- +full:output +full:- +full:name
3 Contact: linux-iio@vger.kernel.org
11 Contact: linux-iio@vger.kernel.org
13 Selects the external clock pin for phase counting mode of
16 MTCLKA-MTCLKB:
18 phase clock.
20 MTCLKC-MTCLKD:
22 phase clock.
26 Contact: linux-iio@vger.kernel.org
33 Contact: linux-iio@vger.kernel.org
39 Contact: linux-iio@vger.kernel.org
45 Contact: linux-iio@vger.kernel.org
52 Contact: linux-iio@vger.kernel.org
59 Contact: linux-iio@vger.kernel.org
78 non-recycle:
80 underflow takes place. The counter is re-enabled when a
84 modulo-n:
94 The output signal is initially low, and will remain low
95 until the counter reaches zero. The output signal then
99 hardware retriggerable one-shot:
100 The output signal is initially high. The output signal
102 low until the counter reaches zero. The output will then
105 value and setting the output signal low, thus starting
106 the one-shot pulse.
109 The output signal is initially high. When the counter
110 has decremented to 1, the output signal goes low for one
111 clock pulse. The output signal then goes high again, the
116 The output signal is initially high.
119 by two on succeeding clock pulses. When the count
120 expires, the output signal changes value and the
126 two on succeeding clock pulses. One clock pulse after
127 the count expires, the output signal goes low and the
129 Succeeding clock pulses decrement the count by two. When
130 the count expires, the output goes high again and the
135 The output signal is initially high. When the count
136 expires, the output will go low for one clock pulse and
141 The output signal is initially high. Counting is started
143 output signal will go low for one clock pulse and then
153 Contact: linux-iio@vger.kernel.org
161 Contact: linux-iio@vger.kernel.org
163 Read-only attribute that indicates the count direction of Count
174 Contact: linux-iio@vger.kernel.org
188 Contact: linux-iio@vger.kernel.org
190 Read-only attribute that indicates whether excessive noise is
195 Contact: linux-iio@vger.kernel.org
207 pulse-direction:
240 What: /sys/bus/counter/devices/counterX/countY/name
242 Contact: linux-iio@vger.kernel.org
244 Read-only attribute that indicates the device-specific name of
245 Count Y. If possible, this should match the name of the
250 Contact: linux-iio@vger.kernel.org
253 On the FlexTimer, the counter clock source passes through a
254 prescaler (i.e. a counter). This acts like a clock
259 Contact: linux-iio@vger.kernel.org
261 If the counter device supports preset registers -- registers
262 used to load counter channels to a set count upon device-defined
263 preset operation trigger events -- the preset count for channel
268 Contact: linux-iio@vger.kernel.org
275 Contact: linux-iio@vger.kernel.org
284 Pulse-Direction count function mode, this Signal is
298 Contact: linux-iio@vger.kernel.org
324 Contact: linux-iio@vger.kernel.org
326 Read-only attribute that indicates the component ID of the
331 Contact: linux-iio@vger.kernel.org
340 Contact: linux-iio@vger.kernel.org
344 rounded-up to a power of 2.
346 What: /sys/bus/counter/devices/counterX/name
348 Contact: linux-iio@vger.kernel.org
350 Read-only attribute that indicates the device-specific name of
351 the Counter. This should match the name of the device as it
356 Contact: linux-iio@vger.kernel.org
358 Read-only attribute that indicates the total number of Counts
363 Contact: linux-iio@vger.kernel.org
365 Read-only attribute that indicates the total number of Signals
370 Contact: linux-iio@vger.kernel.org
372 Read-only attribute that indicates whether a differential
380 Contact: linux-iio@vger.kernel.org
388 Contact: linux-iio@vger.kernel.org
390 Filter clock factor for input Signal Y. This prescaler value
395 Contact: linux-iio@vger.kernel.org
398 non-synchronous load mode.
403 Contact: linux-iio@vger.kernel.org
410 Contact: linux-iio@vger.kernel.org
421 What: /sys/bus/counter/devices/counterX/signalY/name
423 Contact: linux-iio@vger.kernel.org
425 Read-only attribute that indicates the device-specific name of
426 Signal Y. If possible, this should match the name of the
431 Contact: linux-iio@vger.kernel.org
444 Contact: linux-iio@vger.kernel.org
447 non-synchronous or synchronous load mode. Synchronous load mode
448 cannot be selected in non-quadrature (Pulse-Direction) clock
451 non-synchronous:
458 Intended for interfacing with encoder Index output in
459 quadrature clock mode. The active level is configured
462 quadrature clock on the active level of the index input.
466 Contact: linux-iio@vger.kernel.org
468 Read-only attribute that indicates the signal Y frequency, in Hz.